User manual FLAM THEATER MT 68-75 DIMENSIONS

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer . While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Microline are registered trademarks of Oki Electric Industry Company Ltd. EFI, Fiery, the Fiery logo and Spot-On are registered trademarks of Electronics for Imaging, Inc. [. . . ] Typically, letter (or tabloid) pages would be reduced to half-letter (or letter) and printed side by side on both sides of letter (or tabloid) paper, so that the paper can be folded into a booklet. Since this feature prints on both sides of the page, it requires that a duplex unit to be installed in the printer. Notes A few applications do not support booklet printing, but most do. Note that the number of pages in a booklet is always a multiple of four, since two pages are printed on each side of each sheet of paper. If your document is not a multiple of four pages long, the last one, two or three pages in your folded booklet will be blank. ACTIVATING BOOKLET PRINTING 1. On the driver's [Setup] tab, choose [Booklet] from the [Finishing Mode] drop-down list. Click [Options. . . ]. pro930 User's Guide> 57 3. In the Booklet window you can set the [signature] size, the number of [pages] per side of paper, the [binding margin], and if the booklet will be read [Right to Left] or Left to Right. If you do not have the [Booklet] option on the [Setup] tab, check that Duplex is enabled in the driver. (See "Setting the driver device options". ) pro930 User's Guide> 58 COLLATING This feature allows multiple copies of a multipage document to be printed with the pages of each copy in sequence. Uncollated pages print like this: Collated pages print like this: 1 2 3 1 2 3 1 2 3 Application collate--Some application programs have a collate feature in their print options. In this case the application performs the document collation and may send the job multiple times to the printer. Printer collate--This section describes the collate function built into the printer driver. In this case the job is stored temporarily in printer memory or on the printer's hard disk (if installed), and the printer performs collation. On the driver's [Setup] tab, click [Paper Feed Options. . . ]. Click [Resize document to fit printer page] and choose the printer's actual paper size from the [Conversion] drop-down list. It is also possible to select the page size within your software application. See the documentation supplied with your software application for more information. pro930 User's Guide> 64 DUPLEX (DOUBLE-SIDED) PRINTING If your printer has a duplex unit installed you can print on both sides of the paper, to save paper, weight, bulk and cost. > Only paper can be used for duplex printing, not transparencies or other media. If you experience excessive curling with 75­90 g/m² paper, use 105 g/m². Ream wrappers are usually marked with an arrow, indicating which is the print side. > Paper can be fed from standard paper trays, including the high capacity feeder if you have one, but not from the multipurpose tray. > Do not enable the White Page Skip function. pro930 User's Guide> 65 ACTIVATING DUPLEX PRINTING 1. On the driver's [Setup] tab, under [2-Sided Printing], select the binding edge you want. WINDOWS XP For portrait (tall) page layout the usual choice is [Long Edge]. Choosing [None] turns off duplex printing and your document will be printed single-sided. If you have a duplex unit installed, but do not have the [2-sided printing] option on the [Setup] tab, check that the Duplex option is enabled in the driver. [. . . ] For PS, printing is not carried out and the job is cancelled. Auto Continue ON OFF Manual Timeout OFF 30 sec 60 sec OFF 5 sec 10 sec 20 sec 30 sec 40 sec 50 sec 60 sec 90 sec 120 sec 150 sec 180 sec 210 sec 240 sec 270 sec 300 sec Wait Timeout pro930 User's Guide> 144 ITEM Low Toner VALUE Continue Stop DESCRIPTION Sets the printing operation when insufficient toner is detected. ON: continues printing the job, including any jammed pages, once the jam has been cleared. 0. 00 +0. 25 ­ +2. 00 -2. 00 ­ -0. 25 mm 0. 00 +0. 01 ­ +0. 08 -0. 08 ­ -0. 01 in Adjusts the position of the whole printing image (0. 25 mm, 0. 01 in interval) perpendicular to the direction of paper movement (i. e. Adjusts the position of the whole printing image (0. 25 mm, 0. 01 in interval) parallel to the direction of paper movement (i. e. [. . . ]