User manual FRIGIDAIRE FDB1502RGC SERVICE DATASHEET

[. . . ] Exploded View of Wash System Standard Dry Air Flow When the control advances to the "dry" portion of the cycle, a linear actuator retracts a valve, which opens a vent path through the console into the kitchen. The heated, moist air leaving the dishwasher through the console vent causes drier air to be drawn into the unit by way of intake vents located at the bottom of the door. The water on the dishes is evaporated into drier air and the venting process continues. [. . . ] Center the gasket (marked on back) at the tub top center and press in place without stretching or bunching. The gasket takes a short turn at the bottom of the tub channel before ending at the channel end wall. Detergent cover will not latch or open. Replace dispenser. Dishwasher will not pump out. Gasket Cross Section Pump Assembly The pump assembly is driven by a synchronous motor. The motor drives a pump which supplies 100 percent filtered water at a rate of approximately 12 GPM to one spray arm at a time. The spray arm's operation is alternated by small "pauses" of the motor during the wash cycle. is attached by a worm gear clamp to the discharge end of the drain pump. The drain hose must have a loop at a minimum height of 32 inches in order to insure proper drainage. Mounting Rib Dishwasher will not fill with water. 1. Clean float. The main pump can easily be removed by disconnecting the upper spray arm supply tube hose, the drain pump connector hose, the wiring Draining is accomplished by using a small harness connections made at the circulation separate synchronous drain pump mounted to motor, the water heat thermistor located on the the side of the sump. The drain pump is bottom of the pump and rotating the four sump connected to the main pump by a small rubber retainers toward the middle of the sump. The drain check valve is located at the Electrical discharge end of the drain pump. 0. 6 900 Watt Heater Heater Wattage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10. 0 Voltage checks of the heater should be made in Refer to the cycle chart on the reverse side to TempAssure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140°F ±5°F determine when the heater is on during the wash the dry portion of the service test mode. 145°F ±5°F (63°C ±3°C) periods during the drying cycle. 155°F ±5°F (66°C ±3°C) Hi-Limit Thermostat . . . . . . . . . . . . . . . . Install air gap at counter top. Detergent left in dispenser. Water Supply Suggested minimum incoming water temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The manufacturer or seller cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this Service Data Sheet. WATER VALVE CIRCULATION MOTOR FLOAT SWITCH PK HI-LIMIT THERMOSTAT R TOTAL TIME (SEC) DRAIN MOTOR HEATER DISPENSER VENT* WASHING LED SANITIZED LED DOOR L1 BK SWITCH *VENT SYSTEMS W DRAIN MOTOR W WATER VALVE W HEATER W PUMP MOTOR While in idle mode - simultaneously press the HI TEMP and START/CANCEL pads for 3 seconds. 0 0 0 0 1 1 00 X0 0 0 0 0 0 1 00 10 01 X - denotes selectable option CLEAN LED stays on until door is opened or cycle is started. Cycle Selection Options THERMISTOR DISPENSER The dishwasher will then step through the test cycle per the chart. Pushing the START/CANCEL pad will advance the dishwasher to the next step. 1 2 3 4 5 6 7 8 FILL/DISPENSER FILL WASH/HEAT PAUSE/HEAT WASH/HEAT WASH/HEAT/DISP. DRAIN DRAIN/DRY HEAT ON TOTAL 60 27 60 0. 4 75 60 90 90 488 120VAC 60HZ NEUT W 1 1 0 0 0 0 0 0 1 0 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 *SOME MODELS While in power failure mode - simultaneously press the HEAT DRY and START/CANCEL pads for 30 seconds. STEP DRYING LED CLEAN LED The water/service test is a special function initiated from the power failure mode or idle mode. VIO R-BK BU R-Y Y Y W W BK BK W P3-7 P8 P1 W [. . . ]