User manual FRIGIDAIRE FPHD2491KF0 INSTALLATION

[. . . ] It contains important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher. IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch side clearance to open door. [. . . ] Review dimensions in Figure 2 to locate dishwasher's drain, water, and electrical connections. Note: Locate the electrical supply and dishwasher's electrical junction box on right underside of unit behind kickplate assembly. Cut access holes for the Electrical, Water and Drain hoses in the shaded areas as shown in Figure 2. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps. If valve freezes and ruptures, flooding may occur. To install using Top Mount Cabinet Clips: Depending on the depth of cabinet, the Top Mount Clip have a break off point that can be removed if necessary. NOTE: Install Top Mount Clips before unit is installed into the cabinet. Insert the installation brackets to the front top slots of the dishwasher. Install screw through the dishwasher side hole to the wall of cabinet. Reinstall tub cap. Roughing In 3 Electric Shock Hazard Observe all local codes and ordinances for electrical and plumbing connections. All electrical and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury. Make sure your location has the correct drain, water, and electrical outlets to make the connections. Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. High-pressure and high-temperature Stainless Flexible hose with a minimum inner diameter of 1/4" may be used. IMPORTANT: Incoming hot water temperature should be at least 120°F (49°C). Water pressure should be between 20­90 psi. To install the Side Mounting Clips. Depending on space allowed in cabinet the Side Mounting Clips can be installed with the holes for the screw up (preferred method) or down as shown in the illustrations below. NOTE: Install Side Mount Brackets before unit is installed into the cabinet. Adjust accordingly until door opens and closes freely. Parts You Will Need* (Not Included) · Brass Elbow, 90° with a 3/8" National Pipe Thread · Conduit Connector (UL Listed) · Wire Nuts, three (3) for 12-14 gauge wire (UL Listed) * If required: · "Y" Branch Tailpiece and Connector Kit (See Step 4) · Air Gap Kit (See Step 4) All the parts can be found at local hardware, electrical and plumbing supply stores. Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. Figure 4 Figure 2 WATER LINE (NOT INCLUDED) ELECTRICAL BOX Finishing the Water and Electrical Connection 6 GREEN WIRE TO GREEN WIRE (GROUND) BLACK WIRE TO BLACK WIRE (HOT) Finishing the Drain Connection 7 Drain Air Gap Sink at Left check these items: Water and drain lines have no kinks and move freely behind the dishwasher. Review Figures 7, 8 and 9 to see the different ways to connect dishwasher to drain system. Property Damage Do not solder within 6" of the water inlet valve. [. . . ] Make sure hose does not come in contact with any sharp edges. check these items: Sink at Left Sink at Right 2" Drain Hose Hole Figure 7 Checking the Installation Operate the machine through at least one fill and pump-out, checking the following items: At first fill, approximately 1 minute make sure water completely covers filter surface. Water and electrical lines are hooked up to dishwasher. Cabinet Attachment Clips are attached to the cabinet or countertop and kickplate brace. Note: When replacing Kickplate and kickplate brace hand tighten screws. 8 The drain hose loop must be at least 32" high from the floor to insure proper drainage. 2. If you connect to a sink trap, local codes may require you to install an air gap kit, (not included). [. . . ]