User manual FRIGIDAIRE FRA124HT1

[. . . ] All about the Use &Care of your Room Air Conditioner TA B L E O F C O N T E N T S Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2020213A0495 (June 2009) www. frigidaire. com USA 1-800-944-9044 www. frigidaire. ca Canada 1-800-265-8352 Important Safety Instructions NOTE: This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. [. . . ] Once that happens the above steps have to be repeated again. SLEEP FEATURE: YOU WILL SEE: DO THIS: PRESS SLEEP BUTTON Note: In this mode the selected temperature will increase by 2 °F 30 minutes after the mode is selected. The temperature will then increase by another 2 °F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the "Sleep" mode and the unit will continue to operate as originally programmed. The "Sleep" mode program can be cancelled at any time during operation by again pressing the "Sleep" button. All rights reserved. 6 Operating Instructions Operating Instructions (continued) CHECK FILTER FEATURE: YOU WILL SEE: DO THIS: PRESS FILTER RESET BUTTON Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. To reset after cleaning the filter, press the "Filter Reset" button and the light will go off. REMOTE SENSING FEATURE (on some models) LIGHT pulsing ( On & Off intermittently ). DO THIS: PRESS REMOTE SENSING START BUTTON NOTE: Unit display shows the set temperature NOTE: Remote display is actual temperature at remote control only Note: This feature can be activated from the remote control ONLY, the unit must be in a cooling mode. To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing Start button. Next, use the " " buttons to set the desired temperature at the remote. (Note that the set temperature will only be displayed on the unit itself ). The LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it sends a signal. lt will periodically send this signal until the feature is deactivated by pressing the remote sensing Stop button. There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY/HEAT. This is to cover the possibility of having to roll through to select another mode. The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees (in cool mode), 55F and 80F degrees (in heat mode). After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored. 8 2009 Electrolux Home Products, Inc. All rights reserved. Operating Instructions & Care and Cleaning & Energy Saving Ideas Operating Instructions (continued) 4-Way Air Directional Louvers The 4-Way air directional louvers allow you to direct the air flow Up or Down and Left or Right throughout the room as needed. To adjust the air directional louvers side-to-side, use the center handle as you move it side-to-side. (4-WAY) Care and Cleaning Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent shock or fire hazards. Air Filter Cleaning The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils. Be sure filter is thoroughly dry before replacing Or instead of washing, you may vacuum the filter clean. Cabinet Cleaning Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. [. . . ] The consumer will be responsible for diagnostic costs and any removal, transportation and reinstallation costs which are required because of service, costs for labor, parts and transportation other than with respect to the Sealed Refrigeration System. Products with original serial numbers that have been removed, altered or cannot be readily determined. Product that has been transferred from its original owner to another party or removed outside the USA or Canada. Products purchased "as-is" are not covered by this warranty. [. . . ]