User manual FRIGIDAIRE GLHV30T4KW

[. . . ] Note: The instructions appearing in this Owner's Guide are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance. 2 Important Safety Instructions SAVE READ AND SAVE THESE INSTRUCTIONS Take care when using cleaning agents or detergents. Suitable for use in household cooking area CAUTION - To reduce risk of fire and to properly exhaust air, be sure to duct air outside ­ Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. CAUTION - For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors. WARNING ­ TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. [. . . ] 15 or 20 A Dimensions Weight: 30" Model 34 lbs - 36" Model 38, 5 lbs Diameter of Transition 4" 3/4 Figure 1 Diameter of exhaust Duct required 4" 3/4 Considerations before installing Hood 1. For the most efficient air flow exhaust, use a straight run or as few elbows as possible. If allowed in your area, use metallic flex ducting only to connect rigid duct directly to transitions. COLD WEATHER installations should have an additional backdraft damper installed to minimize backward cold air flow and a nonmetallic thermal break to minimize conduction of outside temperatures as part of the ductwork. The break should be as close as possible to where the ducting enters the heated portion of the house. The lower the hood above the cooktop, the more efficient the capturing of cooking odors, grease and smoke. We recommends the hood be installed 18, 5" minimum above an electric cooktop or 25, 6" minimum above a gas cooktop . 4 Installation Tools required for installation Screw driver (pozidrive n°2 ) Electric drill with twist bit Ø 2 mm and Ø 6 mm Pre-Installation consideration The hood can be installed to be used in the following ways: · External exhausting version · Recycling version (with carbon filter to be ordered from your supplier) External Exhausting Version The air is expelled outside by means of a pipe to be connected to the coupling ring B (Figure 2). In horizontal runs, the duct must be slightly slanted (about 10°) and directed upwards to vent the air easily from the room to the outside. A non-return smoke valve is supplied as an optional to be mounted on the coupling flange . B Recycling version Figure 2 The air is filtered through a carbon filter and recycled into the room. If the hood has no filter ask for one from the technical assistance service or the manufacturing company, specifying the hood model. To install the filter, insert it in the place provided and use the two hooks D to fasten it (Figure 4). The filtered air is discharged above the wall cabinet through the baffle E , to be fastened by means of two screws provided directly on the vertical of the outlethole of the hood (if necessary fit a duct Ø120mm from the coupling flange to the upper edge of the hole provided on the top side of the cupboard (Figure 3). E Figure 3 Figure 4 5 Installation Fastening the hood to the wall cabinet Fit the drilling template, which comes with the hood, on the inner right side of the cabinet making sure side "A" coincides with back part. While mounting the hood on the wall cabinet be sure once the hood has been fastened, to allow the wiring compartment to be easily and safely reachable, in order to make eventual safety inspections and/or maintenance operations. Box adjustment Figure 5 The hood can be installed in cabinets with different depths; the front of the box must always be in line with the cabinet. For box adjustment, loosen screws M , slide the square plates P as necessary, and tighten screws M (Figure 7). Ensure that the drawer, when fully retracted, turns OFF all power by acting positively on the rear microswitch. ELECTRICAL GROUNDING INSTRUCTIONS THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW) SERVES TO GROUND THE APPLIANCE. TO PROTECT YOU AGAINST ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE MUST BE CONNECTED TO THE GROUNDING WIRE IN YOUR HOME ELECTRICAL SYSTEM, AND IT MUST UNDER NO CIRCUMSTANCES BE CUT OR REMOVED. Warning: Turn off power circuit at the service panel before wiring this unit. Remove the knockout and install the strain relief (conduit) connector (1/ 2") in junction box. Run 3 wires; black, white and green (#16 AWG) in 1/2" conduit from service panel to junction box. Connect black wire from service panel to black or red in junction box, white to white and green to green-yellow. [. . . ] Products with original serial numbers that have been removed or altered and cannot be readily determined. IF YOU NEED Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the SERVICE warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. [. . . ]