User manual FRIGIDAIRE OVEN CONTROL SERVICE DATASHEET REV A
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FRIGIDAIRE OVEN CONTROL. We hope that this FRIGIDAIRE OVEN CONTROL user guide will be useful to you.
 |
FRIGIDAIRE OVEN CONTROL SERVICE DATASHEET REV A: Download the complete user guide (1476 Ko) |
Manual abstract: user guide FRIGIDAIRE OVEN CONTROLSERVICE DATASHEET REV A
Detailed instructions for use are in the User's Guide.
[. . . ] This service data sheet is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. [. . . ] Before servicing or moving an appliance, remove power cord from electric outlet, trip circuit breaker to Off, or remove fuse. Model C only On Relay Board ELEMENTS Bake Broil Conv P9 P7 P11 Bake Broil Convection Bake Convection Roast Convection Broil Clean Locking / Unlocking Light Door Open Door Closed Relay will operate in this condition only X X X X X X X X X X X X X X X X X X X X* Conv Oven Door DLB Cooling Fan Cooling Fan Fan Light Motor L2 out Low Speed High Speed J3-5 J3-3 J3-4 P1 J3-2 J3-1 X X X X X X X X X X X X X X X X On Display Board The cooling fan is activated at low speed during any cooking function and will remain on until the oven is cools down. The high speed is activated during clean cycles when thetemperatureisaboveapproximately575°Fandduringabroilorconvectionbroil(somemodels)iftheoven door is open. If the control is placed on a lower setting, it is possible for the temperature in the drawer to drop enough to allow the preheat thermostat to close again which will allow the element to reenter the "Preheat" mode at full power. If oven continues to overheat when power is reapplied, RTD sensor probe may have a gone bad. If resistance does not match the chart, replace the RTD sensor thinking a runaway condition exists. [. . . ] J8 Warmer Zone (model C only) pin1 = CR element pin2 = Not used TH1 P1 = P3 = P5 = P15= P7 = P9 = P11= P13= P17= pin 1 = pin 2 = pin 3 = pin 4 = pin 5 = pin 6 = pin 7 = pin 8 = DLB - "Relay" DLB - "Relay" L1-IN L1-IN K3 - "Relay" K5 - "Relay" K7 - "Relay" K21 - "Relay" DLB - "Relay" K18 - "Relay" K16 - "Relay" K14 - "Relay" K11 - "Relay" K9 - "Relay" L1-IN Not used NEUTRAL IN TH1 => Safety Thermostat on Main Back Warmer Zone NEUTRAL Model C only J8 Warmer Zone (model C only) pin1 = CR element pin2 = Not used TH1 P1 = P3 = P5 = P15= P7 = P9 = P11= P13= P17= pin 1 = pin 2 = pin 3 = pin 4 = pin 5 = pin 6 = pin 7 = pin 8 = DLB - "Relay" DLB - "Relay" L1-IN L1-IN K3 - "Relay" K5 - "Relay" K7 - "Relay" K21 - "Relay" DLB - "Relay" K18 - "Relay" K16 - "Relay" K14 - "Relay" K11 - "Relay" K9 - "Relay" L1-IN Not used NEUTRAL IN TH1 => Safety Thermostat on Main Back Warmer Zone NEUTRAL [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FRIGIDAIRE OVEN CONTROL
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FRIGIDAIRE OVEN CONTROL will begin.