User manual FRIGIDAIRE RCM584

[. . . ] Be sure it will support the weight of the unit overan extended period of time. Make sure air conditioner does not fall during installation. Do This First (for existing sleeve) Note that the air conditioner dimensions are: 24" wide, 14" high, and 19" deep (without front). Install Air Conditioner according to these installation instructions to achieve the best performance. Save these installation instructions for future reference. NOTE: DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE Items in Kit You may not need all parts in the kit. [. . . ] Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled. Seal & Frame the unit as described on the last page of these instructions. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page 13. 5 Installation Instructions Wall Sleeve Brands: #3 Fedders or Friedrich 16-3/4" Deep Rear Louvers 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille 4. 5" 80º 50º 50º 4" 80º Top View 2. Attach (2) 4 1 2 " x 3 1 2 " x 1 1 2" centering/support blocks one on each side wall. Cut (2) 17" Tapered Spacer Blocks as shown below into two pieces. 17" 1" 4. 5" 4" 3/4" Tapered Spacer Block Cut Here 12-1/2" 2-1/2" protection Paper Backing 4. The 2 1 2 " section is placed in front of the rib on base with the tapered end facing the back of the sleeve. Cut the remaining portion to 12 1 2" and place behind the rib again sloping toward the rear of the sleeve. Attach (1) 1" x 3/8" x 25" long seal in the center at the top of the sleeve. Attach (2) 1" x 3/8" x 14" seals to the left and right sides of the sleeve. Attach (1) 1" x 3/8" x 25" long seal in the center at the top of the sleeve. Attach (2) 1" x 3/8" x 14" seals to the left and right sides of the sleeve. Cut (2) 1" x 3/8" x 25" long seals to 14" long each and attach to the vertical sections of the grille as shown. Before sliding all-the-way back, remove 2nd screw from front on left side of unit. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled. Seal & Frame the unit as described on the last page of these instructions. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page 13. 4. 5" 4" 8 Installation Instructions Wall Sleeve Brands: #6 Whirlpool 17-1/8" Deep Rear Louvers 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille 80º 4. 5" 50º 50º 4" 80º Top View 2. Cut (2) 17" Tapered Spacer Blocks as shown below into two pieces. 4. 5" 17" 1" 4" 3/4" Tapered Spacer Block 13" Cut Here protection Paper Backing 3. [. . . ] Seal & Frame the unit as described on the last page of these instructions. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page 13. 4. 5" 4" 11 Installation Instructions Wall Sleeve Brands: #9 White Westinghouse or Frigidaire 22" Deep Rear Louvers 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille Because of the increased unit depth, first try dry fitting using the method described below: 2. [. . . ]