User manual FUTUBA R6108SB

[. . . ] R6108SB S. BUS compatible/FASST-2. 4GHz (Multi-ch) system 8 channels/high-speed receiver Usage condition on "High Speed mode" using When servo the high-speed mode, use aorFutaba digital (including brushless servo) S. BUS · The use of analog servos may cause servo trouble. · When using analog servos, select the normal mode, and use channel outputs 7 and 8. Thank you for purchasing a Futaba R6108SB S. BUS compatible receiver. [. . . ] (13. 8g) (*1) Be sure that when using ESC's regulated output the capacity of the ESC must meet your usage condition. R6108SB Specifications What is S. BUS? Different from conventional radio control systems the S. BUS system uses data communication to transmit control signals from a receiver to a servo, gyro, or other S. BUS compatible device. This data includes commands such as "move the channel 3 servo to 15 degrees, move the channel 5 servo to [Connection by S. BUS system] R6108SB Ch output/ Battery terminal 30 degrees" to multiple devices. The S. BUS devices execute only those commands for their own set channel. For this reason, it can be used by connecting multiple servos to the same signal line. 3ch 5ch S. BUS hub S. BUS output S. BUS 2ch S. BUS hub 6ch 4ch Battery Conventional servo S. BUS servo *Can also be used together with conventional servos. Operation Mode Select The operation mode is on "Normal mode" from factory shipping. When to change the mode, please follow the steps shown below. 1 Turn off the receiver. Turn off the receiver. perform linking Do not main wire theconnectedprocedure with motor's is or the engine is operating as it may result in serious injury. really under the control by the transmitter to be linked. WARNING cycle receiver While the linking isif done, please to be linked is power and check the receiver S. BUS Servo Channel Setting Method By doing this step, the mode can switch over between two(2) modes. Turn on the receiver. Press and Hold Function No function To change the mode between Normal and High Speed More than 1 sec. S. BUS servo channel setting can be performed at the R6108SB receiver. 1 Connect the accessory short-plug to the DATA port of the receiver. Short-plug (accessory) LED Status Showing the CURRENT Solid as the mode changed. Red Solid = Normal Red Blink = Normal Green/Red Solid = High Green/Red Blink = Speed High Speed (Become Red after one (1) second) Please check the operation mode by observing the LED when turning on the receiver. If possible there's no FASST transmitter turned on around you in order to make firmer check. When turn on the receiver, the LED will be; · Red when on "Normal mode" · Green and Red (makes Orange) when on "High Speed mode". (After two(2) seconds, change to Red. ) If there are some FASST transmitter turned on around the receiver, the LED may show the above status for a brief moment then changed to the status indication as shown in the "LED indication" table. 2 Connect an S. BUS servo to the conventional system Output connector 1 2 3 4 5 6 7 8 Channel setting Mode A Mode B 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 16 * Connect the short-plug to the DATA port only when an S. BUS servo channel is set. [. . . ] The channel setting is completed in mode B. ) 4 Turn off the receiver. * The LED corresponding to the setting mode blinks. Mode A: Red blinks 3 times Mode B: Green blinks 3 times No function FUTABA CORPORATION 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 1M23N17424 ©FUTABA CORPORATION 2010, 1 (1) [. . . ]