User manual GALAXY 60

[. . . ] GALAXY 8/18/60/500/512 LED 1 (green) door strike open LED 2 (red) door closed GALAXY 512 V1. 10 08:58 TUE 22 NOV LED 3 (red) add mode LED 6 (re programm mode MAX LED 4 (red) void mode LED 5 (red) Nightlock mode 4 7 T 5 8 6 9 < B ent esc 0 # Part Number: L027/D Technical Manuals Online!- http://www. tech-man. com Engineer Manual < 1 2 3 A Galaxy Engineer's Manual Table of Contents Table of Contents Section 1: Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Section 2: System Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Galaxy 8 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Galaxy 18/60 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Galaxy 500 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] All zones in the required (Galaxy 18, 60 & 500) groups that have the omit attribute enabled (refer to option 51. 4 = PROGRAM ZONES. Omit) are omitted when this option is selected. Groups can be omitted and reinstated without setting and unsetting the system. On selecting the Group Omit Option the groups assigned to the user code and keypad are displayed as well as the omit status of each group (Y below the group indicates that it is omitted, N indicates that it is not omitted). NOTE: The zones in the selected groups are omitted from the system as soon as the group is selected. On returning to the banner (normal or engineer) the keypad displays the message ZONES OMITTED. Omitted zones remain omitted for one set period only or until they are manually reinstated to the system. Galaxy 60 & 500 Outputs programmed as Zone Omit (mode programmed as reflex) are activated as soon as the zone is omitted and remains active until the zone is reinstated. If the output mode is programmed as latch, then the Zone Omit outputs activate when the system is set and remain active until the system is unset -- reinstating the omitted zones. Technical Manuals Online!- http://www. tech-man. com 6­41 47 -- Remote Access Option 47 -- Remote Access 1 = Service Galaxy Engineer's Manual This option enables level six users to control the access mode of the Galaxy Gold remote servicing software. There are several options available for increased flexibility and security. NOTE: This option is only available when the Manager Authorise option has been enabled (refer to option 56 = COMMUNICATIONS). If the option is not enabled, the keypad displays NO ACCESS - OPTION DISABLED. 0 = Direct Access: On selecting this option, a 40 minute access period is enabled on the Galaxy panel; Galaxy Gold software can directly access the system during this period. Once access to the panel has been gained, it can maintained indefinitely; there is no maximum duration. On terminating the Galaxy Gold connection to the panel, the access period remains valid for an additional 15 minutes. 1 ­ 5 = Call Back 1 ­ 5 A maximum of five numbers can be preprogrammed by the engineer (refer to option 56 = COMMUNICATIONS). On selecting one of the numbers (1 ­ 5) followed by the ent key, the Galaxy panel dials out to the preprogrammed telephone number associated with the Call Back number If the number selected does not have a preprogrammed telephone number, the system prompts for a one to be entered. Enter the required telephone number and press the ent key; the panel then dials out to the telephone number entered. NOTE: The PC that the panel is dialling to must have Galaxy Gold running in the Waiting for Call-Back mode. Refer to the Galaxy Gold User Guide (L057). 6­42 Technical Manuals Online!- http://www. tech-man. com Galaxy Engineer's Manual 48 -- Engineer Access Option 48 -- Engineer Access (Galaxy 60, 500 & 512) The engineer code is assigned a # in the PIN by default. This prevents the engineer from accessing engineer mode unless authorised to do so by a valid code. To gain access to the engineer menu a level 4, 5 or 6 user must enter their code, and enable the Engineer Access option. This provides a five minute period during which a single entry of the engineer code provides access to engineering mode without causing a tamper alarm. Once the engineer mode has been accessed, there is no time limit on the access period. If the Engineer Mode option has not been enabled, or the code is not entered within the five minute period, then the Engineer code is invalid and has no effect. [. . . ] 1, 212 g A139 RS232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 g A169 Telecom Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 g E050-01 NOTE:The above weights and order codes are for the populated Printed Circuit Board (PCB) only. Modules Weight Galaxy Keypad (Mark II) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]