User manual GEMINI TT-02

[. . . ] OBJECT AND LIQUID ENTRY: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. SERVICING: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. DAMAGE REQUIRING SERVICE: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: · If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal oper ation. [. . . ] NON-USE PERIODS: The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. gROUNDING OR POLARIZATION: · If this product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other), it will fit into the outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. If this product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type power outlet. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. REPLACEMENT PARTS: When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. SAFETY CHECK: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING MOUNTING: The product should not be mounted to a wall or ceil ing. HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Prior to use, we suggest that you carefully read all the instructions. Rotate the PLATTER (2) until the VOLTAGE SELECTION SWITCH (3) (located on the TURNTABLE BASE (1)) is visible through one of the platter holes. Make sure that the VOLTAGE SELECTOR switch is set to the correct voltage. +/-10% Variable pitch slider Solid aluminum platter Straight tonearm for superior tracking Fully adjustable counter weight & anti-skating con trols Dual speed RPM (33/45) LED Illuminated soft touch start/stop & RPM but tons Removable head shell CN-1000 cartridge & felt slipmat included RCA & ground cables Set the TURNTABLE BASE (1) on a flat, level surface free of vibration. Keep the unit away from direct exposure to the sun, heat, moisture or dirt. 1) Because all cartridges have their own designs, please refer to your particular cartridge's instructions to insure proper installation. If you are using a pre-mounted or integrated cartridge, you can jump ahead to HEADSHELL INSTALLATION: 1. For your convenience, the terminals of most cartridges are color-coded. Incase your cartridge is not marked the positive leads are the ones on top negative below, left are left, and right is right. [. . . ] Lower the TONE ARM (7) slowly, while letting go of the TONE ARM (7) over the record where you want to play. When play is over, raise the TONE ARM (7), move it onto the ARM REST (11), and secure it with the ARM CLAMP (10). You now have the option of turning off the power by turning the POWER (13) switch to the "OFF" position, or stopping the PLATTER (2) by pushing the START/STOP (15) button. Pushing the START/STOP (15) button will cause the record to stop exactly when the START/STOP (15) button is pressed while playing. [. . . ]