User manual GEMINI XL-120 MKII

[. . . ] ATTACHMENTS: Do not use attachments not recommended by the product manu facturer as they may cause hazards. WATER AND MOISTURE: Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. ACCESSORIES: Do not place this product on an unstable cart, stand, tripod, brack et, or table. The product may fall, causing serious injury to a child or adult, and seri ous damage to the product. [. . . ] OVERLOADING: Do not overload wall outlets, extension cords, or integral conven ience receptacles as this can result in a risk of fire or electric shock. OBJECT AND LIQUID ENTRY: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. SERVICING: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. DAMAGE REQUIRING SERVICE: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: · If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal oper ation. When the product exhibits a distinct change in performance, this indicates a need for service. REPLACEMENT PARTS: When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. SAFETY CHECK: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING MOUNTING: The product should not be mounted to a wall or ceil ing. HEAT: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. POWER-CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as Prior to use, we suggest that you carefully read all the instructions. Replace and rotate the PLATTER (2) until the MOTOR SPINDLE (4B) is visible, then fit your fingers in hole on the top of the PLATTER (2), feel for and grab the rubber belt and attach to the MOTOR SPINDLE (4B). Set the TURNTABLE BASE (1) on a flat, level surface free of vibration. Keep the unit away from direct exposure to the sun, heat, moisture or dirt. Please contact the Gemini Service Department or your authorized dealer to speak to a qualified service technician. Always begin with the audio level faders/volume controls set at minimum and the speaker volume control(s) set to OFF. Wait 8 to 10 seconds prior to turning up the speaker volume to prevent the transient "POP" that could result in speaker/crossover damage. Because all cartridges have their own designs, please refer to your particular cartridge's instructions to insure proper installation. For your convenience, the terminals of most cartridges are color coded. Mount the cartridge in the HEADSHELL (6) and tighten it with the screws included with the cartridge. [. . . ] Position the tone arm over the desired position on the record and push the CUE LEVER (20) to the "DOWN" position. The TONE ARM (7) will slowly lower onto the record at which time play will begin. When play is over, raise the TONE ARM (7), move it to the ARM REST (11), and secure it with the ARM CLAMP (10). You now have the option of turning off the power by turning the POWER (14) switch to the "OFF" position, or stopping the PLATTER (2) by pushing the START/STOP (17) button and engaging the electronic brake. [. . . ]