User manual GERICOM 5XXC

[. . . ] Table of Contents Chapter 1 : Getting Started 1-1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Powering the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 By AC Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To expend the memory, you have the following choice with different DRAM combination Bank 0 ( 64 Bits) 8 8 16 32 16 32 64 64 32 64 128 64 128 128 128 128 128 Bank 1 ( 64 Bits) 0 8 8 0 16 16 8 16 32 32 0 64 8 16 32 64 128 Power Total Size 8 16 24 32 32 48 72 80 64 96 128 128 136 144 160 192 256 3. 3V User's Manual 2-7 Accessing the Memory Sockets 1. Press the two keyboard latches to elevate the keyboard from its 3. normal position (Figure 2-4). Locate the memory sockets (Figure 2-6 & Figure 2-7). 67. 6mm 31. 75mm Non-component area (The edges of the memory module are the non-component area. ) Figure 2-6 Bank 1 Bank 0 Figure 2-7 Chapter 2: Operation 2-8 Installing Memory Module Follow the steps below to install the memory module: 1. Insert the memory module at a slight angle (45 ) and fit its connectors into the socket firmly (Figure 2-8). Press the two edges of the memory module to make it locked into the place. 6. Figure 2-8 User's Manual 2-9 Removing Memory Module 1. Reinstall the keyboard assembly. Figure 2-9 Chapter 2: Operation 2-10 Using Hard Disk Drive The hard disk drive is mounted in a removable case and can be taken out to accommodate other 2. 5" IDE hard disk drives with a height of 12. 7mm. The system supports PIO mode 4, Master mode IDE, LBA mode and provides a high performance data transfer rate at speeds up to 33 MBytes/second (ATA-33). Removing 1. Press the latch in the indicated direction and take the hard disk drive out of the computer (Figure 2-10). Figure 2-10 Note: When inserting the hard disk drive, Insert it firmly into the computer. Make sure you feel the drive click into the position when it is seated properly. User's Manual 2-11 Replacing Hard Disk Drive The hard disk drive is contained in a case. To take the hard disk drive out of the case and replace with another one, you need to remove the two screws on each side of the case (Figure 2-11). The location of the two screws may be varied depending on different types of hard disk model. Gently disconnect the cable from the hard disk drive when taking it out of the case. Be careful not to bend any pins or crimp the cable. Figure 2-11 Chapter 2: Operation 2-12 Using Floppy Disk Drive The computer is equipped with a removable 1. 44MB, 3. 5" floppy disk drive module. It is usually designated as drive A: by default and can be used as a boot device if properly set in SCU (please refer to Chapter 3: BIOS Utilities). You may replace the floppy disk drive module with a 120MB LS-120 drive (of 12. 7mm high). Contact your dealer for the detail. Inserting/Removing Diskettes When using the floppy drive, always insert your floppy diskette label-side up (Figure 2-12). To remove your diskette, press the eject button on the top-right corner of the floppy drive. Figure 2-12 User's Manual 2-13 Replacing Floppy Disk Drive Note: Before replacing floppy disk drive and CD-ROM module, you need to remove the cover between the two modules. 1. Push the latch in the indicated direction and pull the floppy disk drive module out of the tray (Figure 2-14). Insert the replacement module into the bay. Figure 2-13 Figure 2-14 Chapter 2: Operation 2-14 Using CD-ROM The notebook computer comes standard with a removable 5. 25" CD-ROM module. It is labeled drive D: and may be used as a boot device if properly set. To insert a CD, press the Eject Button and place the CD into the Disc Tray with label-side facing up. [. . . ] Enable enhanced IDE settings. Figure 3-4 Disks Menu User's Manual 3-13 Components Menu Item COM Ports Setting/Option COM A I/O None Settings COM1, 3F8, IRQ4 COM2, 2F8, IRQ3 COM3, 3E8, IRQ10 COM4, 2E8, IRQ11 COM B I/O None Settings COM1, 3F8, IRQ4 COM2, 2F8, IRQ3 COM3, 3E8, IRQ10 COM4, 2E8, IRQ11 Mode Normal (16550) Setting for IrDA (HPSIR) COM B ASK IR FAST IR DMA DMA 0 Setting for DMA 1 Fast IR DMA 3 Port Address Function Specify the COM A configuration. (COM3 & COM4 Only for DOS mode and Non-PnP OS. ) Specify the COM B configuration. (COM3 & COM4 Only for DOS mode and Non-PnP OS. ) Define the COM B hardware. Specify the Fast IR DMA configuration. LPT Port Port Definition DMA Setting For ECP Mode EPP Type None Specify the LPT port and IRQ configuration. LPT1, Addr 378, IRQ7 LPT2, Addr 278, IRQ5 LPT3, Addr 3BC, IRQ7 Standard AT (Centronics) Bidirectional (PS-2) Enhanced Parallel (EPP) Extended Capabilities (ECP) DMA 1 Specify the ECP DMA DMA 3 configuration. [. . . ]