User manual GRACO PUMP-MANIFOLD KITS

[. . . ] 289553 15J747 15J748 15J749 16F420 15J750 15J751 15J752 Lower Part No. 24F417 24F428 24F436 24F444 24F418 24F429 24F437 24F445 Description 750 cc, ChromexTM 1000 cc, Chromex 1500 cc, Chromex 2000 cc, Chromex 750 cc, MaxLife® 1000 cc, MaxLife 1500 cc, MaxLife 2000 cc, MaxLife Ref. Description 24F445 LOWER, 2000 cc, MaxLife cylinder; used in kit 15J752; see 3A0539 for lower parts information LOWER, 750 cc, Chromex cylinder; used in kit 289553; see 3A0539 for lower parts information LOWER, 750 cc, MaxLife cylinder; used in kit 16F420; see 3A0539 for lower parts information O-RING; chemically resistant fluoroelastomer PLUG, manifold Qty 2 24F417 2 24F418 2 41* 45* 111316 n/a 2 2 Parts designated n/a are not available separately. NOTE: The kits include the following parts. Parts included in the kit are marked with an asterisk, for example (13*). [. . . ] Assemble the inlet and outlet manifolds (17) to the lower, using new gaskets (16) and clamps (18). On pumps with a sensor circuit: Install a new black o-ring (41) on the transducer (25a). Torque the adapter (42) first, then the nut (43) to 15-20 ft-lb (21-27 N·m). On pumps without a sensor circuit: Install a black o-ring (41) on the plug (45). Screw the plug into the outlet manifold (17) and torque to 15-20 ft-lb (21-27 N·m). 6. Screw the plug into the inlet manifold (17) and torque to 15-20 ft-lb (21-27 N·m). wrench on the flats of the slider piston (9), to keep it from turning when you are tightening the coupling nut (14). Orient the wrench so it is braced against one of the tie rods (3) or pump stand. Tighten the coupling nut (14) onto the slider piston (9) and torque to 75-80 ft-lb (102-108 N·m). Turn on power and jog the motor to bring the other drive to the bottom of its stroke. NOTE: Update the drive software to reflect the change in size of the lowers. Adjust or repair as necessary before reinstalling in the system. 4 311611D Kit Installation 4 5 7 14 15 Torque to 50-60 ft-lb (68-80 N·m). On pumps without a sensor circuit, install a plug (45) instead of the transducer (25a), 7 7 43 42 25a 15 41* 17* 1 18* 16* 13* 14* PR 7 5 14 *22 *16 9 3 15* 22* 4 16* 18* 41* 45* 17* 7 7 ti8720b FIG. 2: Fluid Section 311611D 5 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. [. . . ] In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www. graco. com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]