User manual HAMMOND XM-2

[. . . ] Model Thank you, and congratulations on your choice of a Hammond XM-2, Drawbar Sound Module. In order to get the most out of this instrument for many years to come, please take the time to read this manual in full. Owner's Manual IMPORTANT SAFETY INSTRUCTIONS Before using this unit, please carefully read this "Safety Instructions" and use it correctly. Please be sure to keep this manual at hand even after reading it once. This "Safety Instructions" section contains very important points for securing your safety. [. . . ] 011 in this example) 3 Touch the [ENTER] button. Touch the [ENTER] button. The Patch will be decided and the following message will appear in the display for a few seconds: Recording Patch . . . When the recording is completed, the display returns to the previous one. NOTE: The recorded Patch data is not lost even after the power is turned off. Owner's Manual 41 DISPLAY AND ITS OPERATION Owner's Manual 42 PLAY MODE The PLAY MODE is the basic display for all the operations. There are two types of PLAY MODE screens to display the Drawbar Registration. One is by showing the length of the Drawbars and the other by digits. To locate this mode: 1. The PLAY mode will be displayed immediately after the power is turned ON and the start-up steps are completed. Touch the [PLAY] button if the displayed mode is wrong. HOW TO READ THE DISPLAY Drawbar Registration UPPER Part/ PEDAL Part/ LOWER Part These two PLAY mode displays (= the bar display and the digital display) will be switched every time you touch the [PLAY] button. In the bar display, the Patch name is shown but another Patch, if assigned to the LOWER Part is not shown. Also, the MIDI IN Note Information is displayed. BAR display Patch Number : Name Sounding on MIDI Note Message The Patch name is not shown in the digital mode display, but you can see the Preset Number of the LOWER Part. DIGITAL display Number on LOWER & PEDAL Part/ Number on UPPER Part Owner's Manual PANEL BUTTON MODE The Panel Button mode is used for controlling the same functions as the knobs and tabs do on the HAMMOND ORGAN. By using the Panel Buttons, the [PARAM] buttons, and the [VALUE] knobs, you can create the basic sounds of the HAMMOND ORGAN. 43 To locate this mode: Touch one of the Panel Buttons you want to set; [DRAWBAR], [PERC], [VIB&CHO], and [LESLIE]. HOW TO READ THE DISPLAY Drawbar registration UPPER Part/ PEDAL Part/ LOWER Part Drawbar Registration mode Selecting FOOTAGE: LEVEL PARAMETER Percussion mode CURSOR In the display window of this keyboard, the CURSOR is displayed in the flashing style, while the most popular indicator- cursor used on the PC, the mobo, etc. is in the shape of an arrow, a square or an I-shape. VALUE CURSOR (Flashing VALUE) BUTTON OPERATION IN THIS MODE Returns to the PLAY mode. These buttons are used to move the CURSOR right or left for selecting the PARAMETER to change. The CURSOR increases or decreases the value of the Parameter. Display And Its Operation 44 MENU MODE The MENU mode is the path for each function. To locate this mode: Touch the [MENU/EXIT] button. There are several pages which contain many various FUNCTION displays. Move from page to page and find the item where you want to go, select item by [PARAM] button, and touch the [ENTER] button to see the desired display. HOW TO READ THE DISPLAY PAGE FUNCTION ITEM (If none, blank. ) BUTTON OPERATION IN THIS MENU Returns to the PLAY mode. Moves from a page to another. Select the FUNCTION ITEM. Enter each FUNCTION MODE. Owner's Manual FUNCTION MODE The FUNCTION MODE is for making each setting and adjustment. There are many displays, but the basic operation is the same. 45 HOW TO READ THE DISPLAY This shows there are PAGEs above (or below). PARAMETER This shows there is a PAGE on the right (or on the left). PAGE NAME VALUE CURSOR (Flashing VALUE) BUTTON OPERATION IN THIS MODE Returns to the PLAY mode. Moves from a page to another. The CURSOR increases or decreases the value of the Parameter. This button is used to move the CURSOR right or left for selecting the PARAMETER to change. The CURSOR moves to the edge of the display and onto the next page (on the right or the left), if there is one. Display And Its Operation 46 EXAMPLE: Adjusting the DECAY TIME of the Percussion [FAST] 1 Go to the MENU Mode. Touch the [MENU] button. The [MENU] mode is displayed. 2 Select the PAGE. Search for the "PERCUS" page, using the [PAGE] button. So select PAGE [B]. 3 Select the FUNCTION. Choose the "PERCUS" by using the [PARAM] button. 4 Touch the [ENTER] button. Touch the [ENTER] button. Now you are on the (first page) of the Percussion Function mode. Owner's Manual 47 5 Move the CURSOR to the Parameter you want to change. DECAY TIME is on the "DECAY" PAGE. Move the CURSOR (flashing value) to underneath "FAST" using the [PARAMETER] button. 6 Change the value. Decrease the value, using the [VALUE] button or the [VALUE] knob. NOTE: Repeat the operation 1 - 6, if you want to change other parameters, too. 7 Back to PLAY mode. Touch the [PLAY] button to return to the PLAY mode. 8 Record a new Patch. The "DECAY FAST" is a Patch Parameter. It will go back to the set value if you call out the other (or current) Patch. [. . . ] By high school, he was working steadily around Philadelphia, receiving first-hand instruction from the top-shelf organists who come through the city such as Jimmy Smith, Jack McDuff, and numerous others. His high visibility career kicked off when Miles Davis asked Joey to join his late 80s band. Joey then signed a contract with Columbia that resulted in five records from 1989 to 1994. With the release of his album, "All of Me" in 1989, Joey emerged on the jazz scene. [. . . ]