User manual HP OFFICEJET 4315

[. . . ] HP Officejet 4300 All-in-One series User Guide HP Officejet 4300 All-in-One series User Guide © Copyright 2006 Hewlett-Packard Development Company, L. P. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under copyright laws. ­ ­ ­ Immigration papers Selective service papers Identification badges, cards, or insignias Governmental stamps: ­ Postage stamps ­ Food stamps Checks or drafts drawn on Governmental agencies Paper currency, traveler's checks, or money orders Certificates of deposit Copyrighted works 11. Use only with the power adapter supplied by HP. Warning 2 The handset ear cap used with this product may attract dangerous objects like pins, staples, or needles. [. . . ] prompt appears, do one of the following: ­ If you want to add another number to the list of junk fax numbers, press 1 to select Yes, and then repeat step 4 for each number you want to block. ­ If you are done, press 2 to select No. To manually enter a number to block 1. This selects Basic Fax Setup and then selects Junk Fax Blocker Set Up. Make sure you enter the fax number as it appears on the display, and not the fax number that appears on the fax header of the received fax, as these numbers can be different. prompt appears, do one of the following: ­ If you want to add another number to the list of junk fax numbers, press 1 to select Yes, and then repeat step 4 for each number you want to block. Remove numbers from the junk fax list If you no longer want to block a fax number, you can remove a number from your junk fax list. This selects Basic Fax Setup and then selects Junk Fax Blocker Set Up. Press 2. 64 HP Officejet 4300 All-in-One series Fax 4. 5. This selects Remove Number from Junk List. prompt appears, do one of the following: ­ If you want to remove another number from the list of junk fax numbers, press 1 to select Yes, and then repeat step 4 for each number you want to block. ­ If you are done, press 2 to select No. Print reports You can set up the HP All-in-One to print error reports and confirmation reports automatically for each fax you send and receive. You can also manually print system reports as you need them; these reports provide useful system information about the HP All-in-One. By default, the HP All-in-One is set to print a report only if there is a problem with sending or receiving a fax. A confirmation message that indicates whether a fax was successfully sent appears briefly on the display after each transaction. Print fax confirmation reports Print fax error reports Fax Print fax confirmation reports If you need printed confirmation that your faxes were successfully sent, follow these instructions to enable fax confirmation before sending any faxes. This means that the HP All-in-One will not print a confirmation report for each fax sent or received. A confirmation message indicating whether a fax was successfully sent appears briefly on the display after each transaction. Press to select one of the following, and then press OK. Off On Fax Send Does not print a fax confirmation report when you send and receive faxes successfully. Prints a fax confirmation report for every fax you send. On Fax Receive Prints a fax confirmation report for every fax you receive. Send & Receive Prints a fax confirmation report for every fax you send and receive. User Guide 65 Chapter 6 Tip If you choose On Fax Send or Send & Receive, and scan your fax to send from memory, you can include an image of the first page of the fax on the Fax Sent Confirmation report. Select On from the Image on Fax Send Report menu. Print fax error reports You can configure the HP All-in-One so that it automatically prints a report when there is an error during transmission or reception. Press to select one of the following, and then press OK. Send & Receive Off On Fax Send Prints whenever there is any kind of fax error. Prints whenever there is a transmission error. Fax On Fax Receive Prints whenever there is a receiving error. Stop faxing You can cancel a fax you are sending or receiving at any time. [. . . ] Note The REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface might consist of any combination of devices subject only to User Guide 123 Chapter 13 the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN for this product is 0. 1B, based on FCC Part 68 test results. Technical information Notice to users in Japan VCCI-2 Notice to users in the European Economic Area This product is designed to be connected to the analog Switched Telecommunication Networks (PSTN) of the European Economic Area (EEA) countries/regions. Network compatibility depends on customer selected settings, which must be reset to use the equipment on a telephone network in a country/region other than where the product was purchased. [. . . ]