User manual HP PSC 2210 ALL-IN-ONE

[. . . ] hp psc 2200 series all-in-one reference guide © Copyright Hewlett-Packard Company 2002 All rights are reserved. No part of the document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. This product incorporates Adobe's PDF technology, which contains an implementation of LZW licensed under U. S. Adobe and the Acrobat logo are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. [. . . ] Your HP PSC only faxes at the highest resolution supported by the receiving fax. If you choose Photo, be aware that the faxing process takes longer to complete. Press Enter to select the desired option. 3 4 5 change contrast Change this setting if you want to send a black and white fax to be darker or lighter than the original. control resolution and contrast 41 hp psc 2200 series 1 2 Press Fax, if not already lit. ­ Or, press until Speed Dials appears, press Enter, then select a speed dial. The circle moves to the left or right, depending on the button you press. Press Enter to use the selected setting. 3 4 5 redial a busy or unanswered number automatically You can set your HP PSC to redial a busy or an unanswered number automatically. The default setting for No Answer Redial is No Redial. 1 2 Press Setup. Press Enter. 3 4 use error correction mode (ECM) ECM eliminates data lost due to poor phone lines by detecting errors that occur during transmission and automatically requesting retransmission of the erroneous portion. Phone charges are unaffected, or may even be reduced, on good phone lines. On poor phone lines, ECM increases sending time and phone charges, but sends the data much more reliably. Turn ECM off (the default setting is on) only if it increases phone charges substantially and you are willing to accept poorer quality in exchange for reduced charges. 1 2 3 4 Press Setup. Press Enter to use the selected setting. 42 use the fax features hp psc 2200 series set automatic reduction This setting determines what your HP PSC does if it receives a fax too large for the default paper size. With this setting on (the default), the image is reduced so that it attempts to fit on one page. With this feature off, the information that will not fit on the first page is printed on a second page. 1 2 3 4 Press Setup. Press Enter to use the selected setting. adjust the volume Your HP PSC provides three levels for adjusting the ring and speaker volume. The speaker volume is the level of everything else, such as the dial and fax tones. Press Enter. change the answer ring pattern (distinctive ringing) Distinctive ring, which allows you to have several phone numbers on the same line, is usually offered by phone companies for an additional fee, and may not be available in all regions. If you do not have this service, leave your HP PSC set to use the default, All Rings. If you connect your HP PSC to a line with distinctive ringing, have your telephone company assign one ring pattern to voice calls and another to fax calls (double or triple rings are best for a fax number). 1 2 3 4 5 Verify that your HP PSC is set to answer automatically. Press to scroll through these options: All Rings, Single Rings, Double Rings, Triple Rings, and Double & Triple. After the ring pattern that the phone company established for this number appears, press Enter. set automatic reduction 43 hp psc 2200 series Tip!We recommend that you use Double Rings or Triple Rings. set up speed dialing Through your HP PSC or your computer, you can assign entries to fax numbers you use often. [. . . ] For each software Product, HP's limited warranty applies only to a failure to execute programming instructions. HP does not warrant that the operation of any Product shall be uninterrupted or error free. HP's limited warranty covers only those defects which arise as a result of normal use of a Product, and does not cover any other problems, including those which arise as a result of (a) improper maintenance or modification, (b) software, accessories, media, or supplies not provided or supported by HP, or (c) operation outside the Product's specifications. For any hardware Product, the use of a non-HP ink cartridge or a refilled ink cartridge does not affect either the warranty to the Customer or any HP support contract with the Customer. [. . . ]