User manual IROBOT BRAVA 380T

[. . . ] Braava ™ Floor Mopping Robot 300 Series Owner’s Manual global. irobot. com Welcome Dear iRobot® Braava™ Owner, Welcome to the world of iRobot. As an owner of the iRobot Braava Floor Mopping Robot, you join a growing group of people around the globe who, like you, are discovering an easier way to mop their floors. The use of practical robots that help you in and around your home is a new reality. We encourage you to share your feedback as we continue to develop new and groundbreaking robots. [. . . ] •  he Navigation System Indicator also indicates Braava’s range. As Braava T gets to the edge of its range (such as going out of the room or far from the NorthStar Navigation Cube) the number of lights will go down. •  raava may occasionally drive back toward the NorthStar Navigation B Cube to confirm its position before continuing on its cleaning path. •  Braava builds a new map each time it starts a new cleaning cycle, but retains its map if paused during the cleaning cycle. Cleaning without a NorthStar Navigation Cube •  Because the Cube is just one part of the Navigation System, Braava can still clean without a NorthStar signal present, however the cleaning area will be much smaller and Braava will not be able to perform edge cleaning in each section. Cleaning with multiple NorthStar Navigation Cubes: (For Braava 380t ONLY): •  raava can use multiple NorthStar Cubes to clean up to 2, 000 square B feet when dry sweeping. Braava will move from one Cube to the next, extending the cleaning area with each Cube it encounters. •  ultiple cubes can be used in Mop mode, too, but Braava limits its wet M cleaning area to 350 square feet to optimize for cloth wetness. Mode Coverage Sweep Mop * Braava 320 800 sq. with additional NorthStar® Cube (sold separately) 16 Braava 300 Series Owner’s Manual Setting Up NorthStar Navigation Cubes Using Braava with one Cube •  Place the Cube near the center of the area you want to clean and start Braava nearby. •  Braava will clean the area around the Cube, and may extend into other rooms based on the cleaning mode and how far the NorthStar signal reaches. •  you have a choice of rooms, place the Cube in a larger room to If maximize NorthStar coverage. •  Once Braava has completed its run, you can move the Cube to clean a different part of your home. Using Braava with multiple Cubes (For Braava 380t ONLY): •  Use one or more extra Cubes (sold separately) to expand how far Braava cleans in a single run. * •  Place extra Cubes in rooms or areas next to the area covered by the first Cube. The Cubes should typically be between 20 and 25 feet from each other for the NorthStar coverage to overlap. •  Braava will automatically clean from one Cube to another. C * ubes are pre-programmed to different NorthStar channels, indicated on the bottom of the Cube. Cubes with different channels must be used for multi-Cube cleaning. 25’ One Cube Multiple Cubes global. irobot. com 17 Operating Braava Put On a Cleaning Cloth 1.  Braava on its end and remove the cleaning pad. Set 2.  Attach a dry or wet cloth to the Multi-Purpose cleaning pad. See the following page for the Pro-Clean Reservoir Pad. 3.  Re-attach the cleaning pad. Magnets will help it snap back into place. 1 2 3 CAUTION: Make sure the cleaning cloth does not drape into the middle channel between the gripping strips as this could impede sensor functions and safe operation. 18 Braava 300 Series Owner’s Manual Using the Pro-Clean Reservoir Pad (Sold separately for Braava 320) The Pro-Clean Reservoir Pad dispenses liquid as Braava mops to keep the cleaning cloth wet longer. Fill the reservoir 1.  pen the fill cap by pulling and swiveling it O to the side. 2.  reservoir with water and replace fill cap, Fill pressing it in securely so it does not leak. 3.  ill the reservoir over a sink as a small F amount of fluid can leak out when the fill cap is closed. Dampen the blue Pro-Clean microfiber 4.  cloth and press onto the velcro strips. Do not use a dry cloth. TIP:  luid dispenses at different rates depending on floor type and solution F used. The first time you mop, start with the cloth only slightly damp and then increase the starting cloth wetness if needed. NOTICE: To avoid the Pro-Clean Reservoir Pad leaving excess fluid on your floor, do not leave Braava unattended when mopping and remove from floor once Braava stops cleaning. When mopping is finished: • Empty any remaining fluid from the reservoir. •  Leave the fill cap open to allow reservoir to dry completely. [. . . ] Try placing Cubes with just 15 feet between them to help Braava connect, then move the Cubes farther apart for subsequent cleaning cycles. The channel number can be found on the bottom of each Cube. Multiples Cubes are Cube channels set up, but Braava is over-cleaning many areas. Pro-Clean Reservoir Pad Troubleshooting Problem: Leaking or leaving puddles. Likely Cause Loose wick or fill cap What To Do Check the fill cap and the wick cap and make sure both are securely sealed shut. Refer to Reservoir Pad maintenance for instructions to replace the wick cap. Not wicking fluid. Wick cap requires replacement global. irobot. com 25 General Troubleshooting Problem: Braava Cleans only a small area. Likely Cause Cube not being used What To Do Make sure the Cube is turned on and placed in the area you want to clean. [. . . ]