User manual JAMICON 3VAAV

[. . . ] This manual, software and firmware described in it are copyrighted by their respective owners and protected under the laws of the Universal Copyright Convention. You may not reproduce, transmit, transcribe, store in a retrieval system, or translate into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, biological, molecular, manual, or otherwise, any part of this publication without the express written permission of the publisher. All product s and t rade names des cribed within are mentioned for identification purpose only. No affiliation with or endorsement of the manufacturer is made or implied. [. . . ] CPU SPEED SEETING Use this menu to specify your settings for CPU/DIMM frequency control. INTEGRATED PERIPHERALS This section page includes all the items of IDE hard drive and Programmed Input / Output features. EXIT WITHOUT SAVE Abandon all CMOS value changes and exit setup. 3VAAV User's Manual 3-3 STANDARD CMOS SETUP The items in Standard CMOS Setup Menu are divided into 10 categories. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. Date The date format is <day>, <date> <month> <year>. day The day, from Sun to Sat, determined by the BIOS and is display-only date The date, from 1 to 31 (or the maximum allowed in the month) month The month, Jan through Dec. year The year, from 1900 through 2099 Time The time format is <hour> <minute> <second>. is 13:00:00. 3-5 3-6 3VAAV User's Manual Primary Master/Primary Slave/Secondary Master/Secondary Slave The categories identify the types of 2 channels that have been installed in the computer. There are 45 predefined types and 4 user definable types are for Enhanced IDE BIOS. Press PgUp or PgDn to select a numbered hard disk type or type the number and press <Enter>. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Type "User" to define your own drive type manually. If you select Type "User", you will need to know the information listed below. Enter the information directly from the keyboard and press <Enter>. This information should be included in the documentation from your hard disk vendor or the system manufacturer. If the controller of HDD interface is ESDI, the selection shall be "Type 1". If the controller of HDD interface is SCSI, the selection shall be "None". If you select Type "Auto", BIOS will Auto-Detect the HDD & CD-ROM Drive at the POST stage and showing the IDE for HDD & CD-ROM Drive. HEADS PRECOMP LANDZONE SECTORS MODE drive type number of cylinders number of heads write precom landing zone number of sectors mode type 3VAAV User's Manual Drive A Type / Drive B Type The category identifies the types of floppy disk drive A or drive B that have been installed in the computer. None No floppy drive installed 360K, 5. 25 in 5-1/4 inch PC-type standard drive; 360 kilobyte capacity 1. 2M, 5. 25 in 5-1/4 inch AT-type high-density drive; 1. 2 megabyte capacity 720K, 3. 5 in 3-1/2 inch double-sided drive; 720 kilobyte capacity 1. 44M, 3. 5 in 3-1/2 inch double-sided drive; 1. 44 megabyte capacity 2. 88M, 3. 5 in 3-1/2 inch double-sided drive; 2. 88 megabyte capacity Video The category selects the type of video adapter used for the primary system monitor. Although secondary monitors are supported, you do not have to select the type in Setup. CGA 40 Color Graphics Adapter, power up in 40 column mode CGA 80 Color Graphics Adapter, power up in 80 column mode MONO Monochrome adapter, includes high resolution monochrome adapters Halt On The category determines whether the computer will stop if an error is detected during power up. [. . . ] parameter setup and to the next drive, If the hard disk cylinder NO. is over 1024, then the user can select LBA mode or LARGE mode for DOS partition larger than 528 MB. supervisor password : can enter and change the options of the setup menus. user password : just can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. 3-13 Exit Selecting SAVE & EXIT SETUP ENTER PASSWORD: Type the password, up to eight characters in length, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. [. . . ]