User manual JBL 62T

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] With the JBL ES Series, innovative technologies such as titanium-laminate-dome tweeters, Elliptical Oblate SpheroidalTM (EOS) waveguides and PolyPlasTM transducer reinforcement are available to you. In addition, the ES150PW/ES250PW's compact enclosure and wireless capability allow for easy integration into any residential environment. Unpacking the Subwoofer If you suspect damage from transit, report it immediately to your dealer. Included 1 x Owner's manual 1 x USA warranty sheet 1 x Subwoofer 1 x 15' Audio cable, RCA-RCA 1 x Transmitter module 1 x Power supply for transmitter 1 x 120V AC power cord for transmitter power supply 1 x 6' Audio cable, RCA-RCA 1 x Wall-mount bracket for transmitter (with two pan-head M3 x 4 machine screws for attaching wall-mount bracket to transmitter) 4 x Small, round, self-adhesive feet ­ to be attached on transmitter's left side panel if transmitter is to be used vertically PLACEMENT Since the installation of a subwoofer can be somewhat more complicated than installing full-range speakers, it is essential that you read this section very carefully prior to connecting the subwoofer to your system. Should you have questions relating to your installation, it is advisable to contact either your dealer or the JBL Customer Service Department for advice. The performance of the subwoofer is directly related to its placement in the listening room and how you align the subwoofer with its satellite speakers. The ES150PW/ES250PW's wireless capability makes it even easier to properly locate the subwoofer in your room. Setting the volume of the subwoofer in relation to the left and right speakers is also of critical importance because it is essential that the subwoofer integrate smoothly with the entire system. Setting the subwoofer's volume level too high will result in an overpowering, boomy bass. Setting the volume level too low will negate the benefits of the subwoofer. Here are several additional facts on installation that may prove useful. When the transmitter receives an audio signal from the source, it will immediately turn on and the LED will turn to blinking green or solid green: RED = STANDBY (No signal detected, transmitter off) GREEN (BLINKING) = Transmitter is on but has not established a link with the wireless sub GREEN (SOLID) = Transmitter is on and has already established a link with the wireless sub The transmitter will automatically enter Standby mode after approximately 10 minutes when no signal is detected from your system. Subwoofer: With the Power Switch ¡ in the "On"position, the Status LED on the back panel will remain lit to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected, amp off) GREEN = SUB ON (Wired signal detected, amp on) ORANGE = SUB ON (Wireless link with transmitter active) The subwoofer will automatically enter Standby mode after approximately 10 minutes when no signal is detected from your system. During periods of normal use, the Power Switch ¡ can be left on. You may turn off the Power Switch ¡ for extended periods of nonoperation (e. g. , when you are away on vacation). Getting Started Confirm that the Status LED on the transmitter is on (red or green), the Status LED on the subwoofer is on (red, orange or green) and an RCA cable is connected from a source unit to either the LFE Input of the subwoofer £ or transmitter < or L and R inputs TM on the subwoofer. If using a wireless connection, the Status LED on the transmitter should be lit in solid green, and the Status LED on the subwoofer should turn orange if connected wirelessly. If the LED on the transmitter is blinking in green and the LED on the subwoofer is in red or green, a wireless link has not been established between the transmitter and the subwoofer. If connecting directly to the subwoofer without using the wireless link, the Status LED on the subwoofer should be lit green. If the LED on the subwoofer remains red, check that the RCA cable from the source to subwoofer (wired connection) or transmitter (wireless connection) is functioning properly and that it is fully inserted at both ends, or that the Transmitter ID-Code Selector B and the Subwoofer ID-Code Selector are set to the same channel. Once you have a green or orange LED on the subwoofer, turn your Subwoofer-Level Control ¶ up halfway so that the knob indicator points up. [. . . ] It also allows for the transmission of high-performance, full-spectrum sound to remote locations, wirelessly. Like all wireless devices, the JBL wireless subwoofer's operating range may vary, depending upon variables such as building construction methods and materials, atmospheric conditions and other sources of interference. Please consult your JBL dealer or distributor, or visit www. jbl. com, for further information or assistance. Wall-Mounting the Transmitter Module NOTE: The customer is responsible for the correct selection and use of mounting hardware (available through hardware stores) that will ensure the proper and safe wall-mounting of the transmitter. [. . . ]