User manual JBL ARCSUB8

[. . . ] Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. Quick stops, excessive force and uneven surfaces may cause the product and cart combination to overturn. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. [. . . ] When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. Do not overload wall outlets, extension cords or integral convenience receptacles, as this can result in a risk of fire or electric shock. Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Do not attempt to service this product your- self, as opening or removing covers may expose you to dangerous voltage or other hazards. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. Objects have fallen onto, or liquid has been spilled into, the product; or c. The product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation; or e. The product exhibits a distinct change in performance ­ this indicates a need for service. Figure 1. Example of Antenna Grounding as per National Electrical Code, ANSI/NFPA 70 22. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " AVERTISSEMENT: "AFIN D'ÉVITER LES DANGERS D'INCENDIE ET D'ÉLECTROCUTION, NE PAS EXPOSER CET APPAREIL À LA PLUIE NI À L'HUMIDITE. " MAIN SPEAKER (8) + AUX IN R ­ ­ L + CD IN IN TAPE OUT IN VCR OUT CENTER SPEAKER (8) SUBWOOFER L This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received including interference that may cause undesired operation. Manufactured under license from Dolby Laboratories Licensing Corporation. "DOLBY, " the double-D symbol and "PRO LOGIC" are trademarks of Dolby Laboratories Licensing Corporation. R ­ + AUDIO + R ­ ­ L + REAR SPEAKER (8) Left Right Left Right Line Out Line Out (Play) Line In (Rec) CD Player Cassette Deck ­7­ three. Push "0" before the number for presets 1­9. To Have the Tuner Search for the Next Strong Station: Power Tuning Auto Power Tuning Auto TUNING UP 1 Tuner 4 5 9 2 6 0 3 Tuner 7 Memory 4 8 1 5 9 2 6 0 3 7 Memory DOWN AUTO 8 Push "Auto" on the receiver or the remote. Push or to search for the next strong station. ­ 10 ­ Power Tuning Auto 1 Tuner 4 8 5 9 2 6 0 P. Scan 3 7 Memory FM/AM CD TAPE AUX/TV Tuner VCR1 VCR2 Sleep Mute Hall Delay 3-Stereo Pro Logic Cent Mode Bypass Center Level Rear Level Surround Volume VOLUME TUNING UP DOWN AUTO POWER (STANDBY) Test Tone SPEAKERS HEADPHONES VIDEO VIDEO 2 L ­ AUDIO ­ R PRO LOGIC 3 STEREO HALL CENTER MODE TEST TONE BYPASS FM/AM CD TAPE VCR1 VCR2 AUX/TV BALANCE BASS TREBLE L R MIN MAX MIN MAX ­ 11 ­ To Switch Between Different Sources: P. Scan FM/AM TEST TONE BYPASS FM/AM CD TAPE VCR1 VCR2 AUX/TV CD TAPE AUX/TV Tuner Power Tuning Auto VCR1 VCR2 Sleep Mute 1 2 6 0 P. Scan FM/AM 3 7 Memory Hall 3-Stereo Pro Logic Tuner 4 8 5 9 Push FM/AM, CD, Tape, VCR1, VCR2 or AUX on the receiver or the remote. CD TAPE AUX/TV Tuner VCR1 VCR2 Sleep Mute Hall Delay 3-Stereo Pro Logic Cent Mode Bypass Center Level Rear Level Surround Volume VOLUME TUNING UP DOWN AUTO POWER (STANDBY) Test Tone SPEAKERS HEADPHONES VIDEO VIDEO 2 L ­ AUDIO ­ R PRO LOGIC 3 STEREO HALL CENTER MODE TEST TONE BYPASS FM/AM CD TAPE VCR1 VCR2 AUX/TV BALANCE BASS TREBLE L R MIN MAX MIN MAX ­ 12 ­ Surround-Mode Operation What is Dolby* Pro Logic*?Dolby* Pro Logic* is an encode/decode process by which four channels of soundtrack information are encoded into two channels for playback on VCRs, laser disc players and some TV broadcasts, and then decoded back into four channels for playback through five loudspeakers. Remember that a Dolby Pro Logic system consists of three channels of information for front left, center and right speakers, and one channel of mono surround information. Dolby Pro Logic helps to re-create all of the impact and excitement of a movie theater in your home. This system contains four surround modes. Dolby 3 Stereo ­ In this mode the surround channels do not operate. This may be preferred when listening to a music source that was not recorded with surround channel information. Hall ­ Use this mode to create a surround image from 2-channel recording. [. . . ] · Make sure there is a source ­ for example, a VCR or television ­ hooked up to the VCR or tape/aux input jacks on the receiver. If most of the sound comes from the center-channel speaker, with little or no information from the surround channels, note the following: Although most of today's televisions are equipped with stereo audio output jacks, some stereo televisions have poor audio sections and are unable to provide a Dolby Pro Logic encoded signal. In the unlikely event that you experience this problem, connecting the audio outputs from your Hi-Fi VCR, laser disc player, DVD player or satellite receiver directly to one of the inputs on the receiver will provide a proper audio signal and allow you to enjoy true Dolby Pro Logic surround sound. If there is no sound from the surround speakers or it is very low, check the following: · Check all connections between amplifier and each of the speakers. [. . . ]