User manual JBL CVSAT50PAIR

[. . . ] The S36AWII loudspeakers are weather-resistant and are specifically designed for outdoor use, such as in a patio area. As noted below, we recommend mounting the speakers under an overhang, such as roof eaves, for added protection. The S36AWII speakers, because they are resistant to moisture, are also appropriate for mounting in a bathroom, although not inside a bathtub or shower stall. More than 6 ­ 8 feet For home theater applications: 0-2 ft. This placement provides a wide spread in sound, supplemented by the center channel speaker. Although these loudspeakers are designed as a mirrored pair, the decision as to which one is left or right will depend on the amount of space left between them. A wider stereo image is presented with the tweeter/midrange array outboard, and a tighter image is presented with the array inboard. WALL-MOUNTING Do not attempt to mount these speakers on a ceiling, on the underside of roof eaves or in a shower stall. [. . . ] The S36II and S36AWII loudspeakers may be positioned on the wall either horizontally or vertically. The grille logo on each speaker may be rotated depending on how the speaker is positioned. Gently pull the logo away from the grille slightly, rotate it to the desired position, and let go. When mounted vertically, the tweeter array may be positioned either up or down, depending on the height of the placement. If the speakers will be above ear level, the tweeter array should be positioned down, preferably no more than two feet above ear level. If the speakers will be mounted very low, it may be best to position the tweeter array upward so that it will be no more than two feet below ear level. The S36II and S36AWII enclosures are specially designed to angle the speakers toward the listener when mounted flush against the wall. When mounting the S36AWII speakers outdoors, we recommend that you place them under an overhang, such as roof eaves, for added protection, and that you use two of the supplied special angle-mount screws per speaker, which angle the speakers downward at a greaterthan-usual angle, facilitating water drainage. NOTE: When using the enclosed angle-mount screws, always use the top two screw locations appropriate for the specific mounting orientation of your S36AWII. Referring to the enclosed installation template, screw locations (1) and (2) are to be used when mounting the S36AWII horizontally so that these locations are on top. Insert the bare end of the wire through this hole; then screw the collar down until the connection is tight. The hole in the center of each collar is intended for use with bananatype connectors. TROUBLESHOOTING If there is no sound from any of the speakers: · Check that receiver/amplifier is on and that a source is playing. If the system plays at low volumes but shuts off as volume is increased: · Check all wires and connections between receiver/ amplifier and speakers. · If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/ amplifier. If there is no sound coming from one speaker: · Check the "Balance" control on your receiver/amplifier. · Check all wires and connections between receiver/amplifier and speakers. Make sure no wires are touching other wires or terminals and creating a short circuit. · In Dolby* Digital or DTS® mode, make sure that the receiver/ processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place, i. e. , the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved, i. e. , the speaker that was not working still has no sound and the speaker that was working is still fine. [. . . ] · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place, i. e. , the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved, i. e. , the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at www. jbl. com for further information. S P E C I F I C AT I O N S S36II/S36AWII Description: S36II ­ 3-Way 6" horizontal/vertical mirror-image wall-mount/ bookshelf loudspeakers S36AWII ­ 3-Way 6" horizontal/vertical mirror-image wall-mount/ bookshelf, weather-resistant loudspeakers Maximum Recommended Amplifier Power:** Nominal Impedance: Sensitivity (2. 83V/1m): Frequency Response (­3dB): Crossover Frequencies: High-Frequency Transducer: Midrange Transducer: 150W 8 Ohms 90dB 60Hz ­ 20kHz 650Hz, 3000Hz 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate SpheroidalTM (EOS) waveguide S36II ­ 4" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, shielded; Linear Field ProximityTM (LFP) bezel (model S36AWII uses a shielded WeatherPlasTM midrange) S36II ­ 6" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, SFGTM magnetic shorting rings, high-temp oversized Kapton® voice coil, , HeatScapeTM motor structure, cast-aluminum baskets, shielded (model S36AWII uses a shielded WeatherPlasTM woofer) Low diffraction, IsoPowerTM Sealed Straight-Line Signal PathTM (SSP) All-metal, gold-plated, 5-way binding posts 10-1/4" x 14-5/8" x 5" 260mm x 371mm x 127mm 11 lb/5kg We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the loudspeakers described in this owner's manual are in compliance with technical standards: Low-Frequency Transducer: Baffles: Enclosure: Network: Terminals: Dimensions (H x W x D): Weight: * Dolby is a trademark of Dolby Laboratories. [. . . ]