User manual JBL ES150P

[. . . ] To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle. The mains plug of the power supply cord shall remain readily operable. Do not expose batteries to excessive heat such as sunshine, fire or the like. [. . . ] Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. Auto On/Standby With the Power Switch 5 in the ON position, the Status LED on the top will remain lit in red or green to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected, Amp Off) GREEN = ON (Signal detected, Amp On) The subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system. You may turn off the Power Switch 5 for extended periods of nonoperation, e. g. , when you are away on vacation. Adjust Gain Turn your Subwoofer-Level Control 2 up to the halfway position. If no sound emanates from the subwoofer, check the AC-line cord and input cables. Once you have confirmed that the subwoofer is active, proceed by playing a CD, record or cassette. Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer-Level Control 2 until you obtain a pleasing blend of bass. Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but never obtrusive. [. . . ] In the event that your subwoofer ever needs service, contact your local JBL dealer or distributor, or visit www. jbl. com for a service center near you. 6 SPECIFICATIONS ES150P Frequency Response Amplifier RMS Power Amplifier Peak Dynamic Power Crossover Frequency 27Hz ­ 150Hz 300 Watts 500 Watts 50Hz ­ 150Hz; 24dB/octave, continuously variable 250mm (10") PolyPlasTM 457mm x 337mm x 387mm (18" x 13-1/4" x 15-1/4") 17. 7kg (39 lb) ES250P 25Hz ­ 150Hz 400 Watts 700 Watts 50Hz ­ 150Hz; 24dB/octave, continuously variable 300mm (12") PolyPlasTM 502mm x 400mm x 428mm (19-3/4" x 15-3/4" x 16-7/8") 19. 5kg (43 lb) Driver Dimensions (H x W x D) (with grille) Weight The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off. Declaration of Conformity Declaration of Conformity We, Harman Consumer Group, Inc. 2, route de Tours 72500 Château du Loir France declare in own responsibility that the product described in this owner's manual is in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 We, Harman Consumer Group, Inc. 2, route de Tours 72500 Château du Loir France declare in own responsibility that the product described in this owner's manual is in compliance with technical standards: EN 55013:2001+A1:2003 EN 55020:2002+A1:2003 EN 61000-3-2:2000 EN 61000-3-3:1995+A1:2001 EN 60065:2002 Laurent Rault Harman Consumer Group, Inc. [. . . ]