User manual JBL GTO 5355
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JBL GTO 5355. We hope that this JBL GTO 5355 user guide will be useful to you.
 |
Manual abstract: user guide JBL GTO 5355
Detailed instructions for use are in the User's Guide.
[. . . ] · Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. Specifications · 55W RMS x 4 channels, plus 225W RMS x 1 @ 4 ohms and 1% THD + N* · 75W RMS x 4 channels, plus 360W RMS x 1 @ 2 ohms, 14. 4V supply and 1% THD + N* · 150W RMS x 2 channels @ 4 ohms, plus 360W RMS x 1 @ 2 ohms, 14. 4V supply and 1% THD + N* · Frequency response: 10Hz 83kHz and 20Hz 250Hz (3dB) · Maximum input signal: 6V* · Maximum sensitivity: 100mV* · THD + N: 0. 03% · Signal-to-noise ratio: 85dBA (reference 1W into 4 ohms)* · Signal-to-noise ratio: 104dBA (reference rated power into 4 ohms) * CEA-2006A-compliant Speaker Output Connectors · Connect the speakers to these terminals, observing proper polarity. [. . . ] · HPF: Select for midrange speakers or full-range speakers when a subwoofer is used in the system. Subwoofer Input Connector (RCA) · Connect to the subwoofer RCA outputs from the source unit, or signal processor. · FLAT: Select for full-range speakers when no subwoofer will be used in the system. · HPF: Select for midrange speakers or full-range speakers when a subwoofer is used in the system. Rear Crossover-Frequency Control · 12dB/octave crossover, variable from 32Hz to 320Hz. Rear Input-Level Control · Used to match the rear input of the amplifier to the output of the source unit. Rear Input Connectors (RCA) · Connect to rear RCA outputs from the source unit, or signal processor. EXT/INT Switch · If the source unit has a subwoofer output and you have connected it to the SUB input, set this switch to the EXT position. Optional Subwoofer Remote Level Control Connector · Connect the Remote Level Control (RLC) here, using the RJ-11 cable (supplied with the RLC).
Subwoofer Level Control · Used to match the SUB input of the amplifier to the output of the source unit. Protect LED · Illuminated under any of the following fault conditions: battery over/under voltage, short circuit in speaker wires, amplifier is too hot, amplifier's output circuit has failed (DC voltage present in the amplifier's output). Subwoofer Low-Pass Filter Frequency Control · 12dB/octave low-pass filter, variable from 20Hz to 200Hz. DBO (Dynamic Bass Optimization) Variable Subsonic High-Pass Filter With Variable Boost (Q) · For woofers in tuned (vented) enclosures, set the Frequency control to a value 10Hz below the enclosure's resonance (tuned) frequency. [. . . ] Remote Level Control (Optional) The Remote Level Control, if installed, will allow you to adjust the level of bass while seated in the listening position.
This product is designed for mobile applications and is not intended for connection to the mains. Features, specifications and appearance are subject to change without notice.
Declaration of Conformity
Harman International, Consumer Division 8500 Balboa Boulevard, Northridge, CA 91329 USA www. jbl. com © 2009 Harman International Industries, Incorporated. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JBL GTO 5355
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JBL GTO 5355 will begin.