User manual JBL HTI6

[. . . ] Logo to be attached to grille depending on vertical or horizontal installation. HTI6C Template/paint shield (punch out at perforation). One pair of speakers with grilles. Template/paint shield (punch out at perforation). 2 SPEAKER PLACEMENT FRONT SPEAKERS (HTI6, HTI8, HTI55) English 400 ­ 600 MODELS HTI6, HTI8 AND HTI55 AS REAR SPEAKERS 5 ­ 6 ft. WALL WALL WALL WALL MODEL HTI6C IN CEILING be placed at about the same height from the floor as the listeners' ears will be, with the tweeters aimed toward the listening position at ear-level height. Model HTI55 is suitable for the front left, center and right positions, and it may also be used as a side surround or surround back speaker. [. . . ] Greater than 30 ft. 16 gauge 12 gauge 10 gauge INSTALLATION The JBL HTI Series in-wall speakers were designed to be easily installed. However, if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Tools Needed Pencil Phillips #2 screwdriver Measuring tape Utility knife Carpenter's level Awl 4 EXISTING CONSTRUCTION HTI6, HTI8, HTI55 Level 1/2" 1/2" 1/2" Template Remove the grille from the speaker frame by pulling on the paper tab. If the tab is missing, to avoid scratching the grille or baffle you may unfold a paper clip, insert the straight end through one of the holes in the grille, and gently pull up. Determine the correct speaker location. Note: Remove the inner template, which is the paint shield, at the perforation. Although the HTI55 may be oriented either horizontally or vertically, the installation procedure is the same. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place. Cut the drywall. Connect the speaker wires to the speaker. Place the frame assembly in the wall. Screw down each of the four (six for HTI55) Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall. The HTI speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grille, gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further. You may also rotate the tweeter to orient the JBL logo as desired. Replace the metal grille. For the HTI55 only, attach the JBL logo to the grille to correspond to vertical or horizontal installation. 5 English EXISTING CONSTRUCTION English HTI6C 1/2" 1/2" 1/2" Remove the grille from the speaker frame by pulling on the paper tab. If the tab is missing, to avoid scratching the grille or baffle you may unfold a paper clip, insert the straight end through one of the holes in the grille, and gently pull up. Determine the correct speaker location. Note: Remove the inner template, which is the paint shield, at the perforation. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place. Connect the speaker wires to the speaker. Place the frame assembly in the wall. The HTI speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grille, gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. [. . . ] · Check all wires and connections between receiver/amplifier and speakers. Make sure none of the speaker wires are frayed, cut or punctured. 7 SPECIFICATIONS HTI6 English Frequency Response HTI8 Frequency Response HTI55 Frequency Response HTI6C Frequency Response 38Hz ­ 20kHz (­10dB) Recommended Maximum Amplifier Power 30Hz ­ 20kHz (­10dB) Recommended Maximum Amplifier Power 40Hz ­ 20kHz (­10dB) Recommended Maximum Amplifier Power 40Hz ­ 20kHz (­10dB) Recommended Maximum Amplifier Power 100 watts Impedance 120 watts Impedance 120 watts Impedance 100 watts Impedance 8 ohms nominal Sensitivity 8 ohms nominal Sensitivity 8 ohms nominal Sensitivity 8 ohms nominal Sensitivity 88dB (2. 83V/1m) Crossover Frequency 90dB (2. 83V/1m) Crossover Frequency 88dB (2. 83V/1m) Crossover Frequency 88dB (2. 83V/1m) Crossover Frequency 2, 500Hz Woofer 2, 500Hz Woofer 2, 000Hz Woofer 2, 000Hz Woofer 6-1/2" Polymer-coated aluminum cone w/rubber surround Tweeter 8" Polymer-coated aluminum cone w/rubber surround Tweeter Dual 5" polymer-coated aluminum cone w/rubber surround Tweeter 6-1/2" Polymer-coated aluminum cone w/rubber surround Tweeter 1" Pure-titanium dome, w/Elliptical Oblate SpheroidalTM (EOS) waveguide, and swivel mount Plate Size (W x H) 1" Pure-titanium dome, w/Elliptical Oblate SpheroidalTM (EOS) waveguide, and swivel mount Plate Size (W x H) 1" Pure-titanium dome, w/Elliptical Oblate SpheroidalTM (EOS) waveguide, and swivel mount Plate Size 1" Pure-titanium dome, w/swivel mount Plate Size (Diameter) 233mm (9-3/16") Mounting Cutout Size (Diameter) 216 x 279mm (8-1/2" x 11") Mounting Cutout Size (W x H) 257 x 333mm (10-1/8" x 13-1/8") Mounting Cutout Size (W x H) 391 x 191mm (15-3/8" x 7-1/2") Mounting Cutout Size 181 x 246mm (7-1/8" x 9-11/16") Mounting Depth 225 x 300mm (8-7/8" x 11-13/16") Mounting Depth 56 x 152mm (14" x 6"3) Mounting Depth 200mm (7-7/8") Mounting Depth 98mm (3-7/8") Weight per Speaker 102mm (4") Weight per Speaker 98mm (3-7/8") Weight per Speaker 108mm (4-1/4") Weight per Speaker 5kg (11 lb) 6. 1kg (13. 5 lb) 2. 6kg (5. 7 lb) 4. 5kg (10 lb) All features and specifications are subject to change without notice. [. . . ]