User manual JBL CONTROL NOW AW

[. . . ] ® JBL CONTROL SERIES JBL CONTROL NOWTM JBL CONTROL NOWTM AW ® ® OWNER'S GUIDE TABLE OF CONTENTS UNPACKING THE SPEAKERS . 28 JBL CONTROL NOWTM LOUDSPEAKERS For more than 60 years, we have been providing JBL® audio equipment for top concert halls, recording studios and movie theaters around the world, becoming the hands-down choice of leading recording artists and sound engineers. With JBL Control NOWTM loudspeakers, innovative technologies such as titaniumlaminate dome tweeters, PolyPlasTM transducer reinforcement and a patented, controlled-directivity Bi-Radial® horn are available to you. JBL Control NOW speakers are unique in their ability to deliver excellent performance over an extremely wide listening area. [. . . ] Secure the mounting- bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting bracket and tightening. Repeat the process with the remaining speaker. Mounting-Bracket Cap 5. Now rest the second JBL Control NOW speaker's rear flange in the mounting bracket, as shown, and complete the process. Secure the mounting-bracket cap with two #10-32 x 2" (M5 51 mm) screws through the bottom of the mounting bracket. Mounting Bracket (side view) #10-32 x 2" Screws (2) #10-32 x 2" (M5 51 mm) Screws (2) (side view) 6. To orient the JBL logo into the correct position, pull the JBL logo slightly outward from the speaker grille and rotate. Peel the adhesive cover off the mounting-bracket covers and attach to the top and bottom of the mounting assembly. Mounting-Bracket Covers #10-32 x 2" (M5 51 mm) Screws (2) Mounting-Bracket Covers 13 English 3/4-ROUND WALL-MOUNTING Speaker 1 When deciding upon a location for the JBL Control NOW speaker, take care NOT to install the mounting bracket closer than 3" (7, 6 cm) to the ceiling. Any closer than 3" (7, 6 cm) will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket. ceiling 3" (7, 5 cm) Minimum distance from ceiling to top of bracket (horizontal mounting) Speaker 2 Speaker 3 2. CAUTION The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the speakers. However, if you are unable to clearly and fully understand and follow the instructions in this manual, or if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. Power tools can exert excessive and unnecessary torque which, in turn, can damage fasteners or other parts and accessories, reducing their strength and causing possible failure of the fastener or part. A failed or damaged fastener or part may not be able to perform as designed, and may lead to an unsafe installation. Secure three corner/wall-mounting brackets together by using four #10-32 x 1/2" (M5 13 mm) screws provided as shown. Appropriate anchors 3. The terminal assembly is removed by giving it a slight counterclockwise rotation. Use the transparent plastic strap to pull the assembly out, as shown. #10-32 x 1/2" (M5 13 mm) Screws (2) #10-32 x 1/2" (M5 13 mm) Screws (2) 14 4. Connect the small end of the multiunit wiring adapter to the rear of speaker 1, as shown. 6. Place the large end of the multiunit wiring adapter that is already connected to speaker 1 into speaker 2 by sliding the multiunit wiring adapter into the rear of the speaker at a slight angle and rotate clockwise. This end is connected to the first speaker now resting in the Corner/Wall-Mount Bracket. 5. The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting-bracket cap with two screws through the bottom of the mounting bracket. Run the loose end of the multiunit wiring adapter through the rear cable-management hole in the mounting bracket and rest the JBL Control NOW speaker's rear flange in the mounting bracket, as shown. Secure the mounting-bracket cap by inserting two #10-32 x 2" (M5 51 mm) screws (provided) in the bottom of the mounting bracket and tightening. 7. Connect the small end of an additional multiunit wiring adapter to the speaker rear as shown. This end is connected to the first speaker now resting in the Corner/Wall-Mount Bracket. 8. Rest the second JBL Control NOW speaker's rear flange in the mounting bracket, as shown, and complete the process. Secure the mounting bracket cap with two #10-32 x 2" (M5 51 mm) screws through the bottom of the mounting bracket. #10-32 x 2" (M5 51 mm) Screws (2) Mounting-Bracket Cap #10-32 x 2" Screws (2) Mounting Bracket (side view) #10-32 x 2" (M5 51 mm) Screws (2) (side view) 15 English 9. [. . . ] The side of the wire with a ridge or other coding is usually considered positive polarity (i. e. , +). NOTE: If desired, consult your local JBL dealer about speaker wire and connection options. 1. Insert bare end; release push connector BLACK = -- RED = + Pole-Mount Bracket The speakers have coded terminals that accept a variety of wire connectors. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown. [. . . ]