User manual JBL L36

[. . . ] To comply with European CE certification, these holes are blocked with plastic inserts at the point of manufacture. Do not remove these inserts if you are using the product in an area covered by the European CE certification. BI-WIRING The bi-wire connection method requires one amplifier and two sets of speaker wires. [. . . ] By removing the shorting bars, connections may be made to the individual network sections using four conductors, one for each of the four terminals. For single-wire connection, leave the shorting bars in place and connect only a single set of speaker wires (two conductors) to the two upper terminals. MODELS: E30, EC35, E50 MODELS: E30, E50, E60, E80, E90, E100 RIGHT LEFT The supplied self-adhesive rubber feet may be attached to the bottom corners of your speakers to protect your furniture. MODELS: E60, E80, E90, E100 ­ + ­ + ­+ RIGHT ­ + LEFT Receiver's Speaker Outputs MODEL: EC35 CENTER ­ ­ + + These models feature four rubber feet that enable them to be placed on a smoothsurfaced floor, such as tile or hardwood. Four metal spikes are supplied for use when the speaker is to be placed on a carpeted surface, to decouple the speaker from the floor and prevent unwanted damping. To insert the spikes, gently lay the speaker on its side (not its front or back) on a soft, nonabrasive surface. Each spike screws into the threaded insert in the center of each rubber foot. NEVER drag the speaker to move it, as this will damage the spikes, the feet and/or the wood cabinet itself. CAUTION: Floorstanding (tower) loudspeakers have a high center of gravity and may become unstable and tip over during earthquakes, or if rocked, tipped or improperly positioned. If this is a concern, these speakers should be anchored to the wall behind them, using the same procedures and hardware customary for anchoring bookcases and wall units. · In Dolby* Digital or DTS® modes, make sure that the receiver/processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem has followed the speakers, or has remained in the same channel. If the problem is in the same channel, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit www. jbl. com for further information. · Make sure the polarities (+ and ­) of the left and right "Speaker Inputs" are connected properly. · Consider adding a powered subwoofer to your system for use with digital ". 1" surround formats. Declaration of Conformity We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1997 Gary Mardell Harman Consumer International Chateau-du-Loir, France 8/03 SPECIFICATIONS E30 Description 2-Way 6" bookshelf E50 E60 E80 Description 3-Way dual 6" floorstanding Max. Recommended Amplifier Power** 200W Power Handling (Continuous/Peak) 100W/400W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 91dB Frequency Response (­3dB) 38Hz ­ 20kHz Crossover Frequencies 300Hz, 4000Hz High-Frequency Transducer 19mm Titaniumlaminate dome, shielded E90 Description 3-Way dual 8" floorstanding Max. Recommended Amplifier Power** 225W Power Handling (Continuous/Peak) 110W/440W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 91dB Frequency Response (­3dB) 36Hz ­ 20kHz Crossover Frequencies 300Hz, 4000Hz High-Frequency Transducer 19mm Titaniumlaminate dome, shielded Midrange Transducer 100mm PolyPlas, TM shielded Low-Frequency Transducers Dual 200mm PolyPlas, TM shielded Baffle Low diffraction, IsoPowerTM Port FreeFlowTM flared Network Straight-Line Signal PathTM (SSP) E100 Description 3-Way dual 10" floorstanding Max. [. . . ] Recommended Amplifier Power** 225W Power Handling (Continuous/Peak) 110W/440W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 91dB Frequency Response (­3dB) 36Hz ­ 20kHz Crossover Frequencies 300Hz, 4000Hz High-Frequency Transducer 19mm Titaniumlaminate dome, shielded Midrange Transducer 100mm PolyPlas, TM shielded Low-Frequency Transducers Dual 200mm PolyPlas, TM shielded Baffle Low diffraction, IsoPowerTM Port FreeFlowTM flared Network Straight-Line Signal PathTM (SSP) E100 Description 3-Way dual 10" floorstanding Max. Recommended Amplifier Power** 250W Power Handling (Continuous/Peak) 125W/500W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 91dB Frequency Response (­3dB) 33Hz ­ 20kHz Crossover Frequencies 1000Hz, 5000Hz High-Frequency Transducer 19mm Titaniumlaminate dome, shielded EC35 Description 3-Way dual 5" center Max. Recommended Amplifier Power** 150W Power Handling (Continuous/Peak) 75W/300W Nominal Impedance 8 Ohms Sensitivity (2. 83V/1m) 91dB Frequency Response (­3dB) 75Hz ­ 20kHz Crossover Frequencies 800Hz, 3200Hz High-Frequency Transducer 19mm Titaniumlaminate dome, shielded Description Description 3-Way, 8" 3-Way 8" horizontal/vertical floorstanding mirror-image bookshelf Max. [. . . ]