User manual JBL LX600

[. . . ] All rights reserved. JBL SIS Products Group 8500 Balboa Boulevard Northridge, CA 91329 250 Crossways Park Drive Woodbury, NY 11797 800-336-4JBL This document should not be construed as a commitment on the part of JBL Synthesis. JBL Synthesis assumes no responsibility for errors that may appear within this document. © 2003 Harman international Industries, Incorporated, All rights reserved. "Lexicon, " "LOGIC7, " and the L7 logo are registered trademarks of Harman International Industries, Inc. [. . . ] When set to OFF, the display device shows the on-screen display in the same aspect ratio as the input signal. * Aspect ratio refers to the size of the picture on the display device screen or to the size of the display device screen. A 16:9 aspect ratio, often referred to as "widescreen, " is almost twice as wide as high. 3-22 SDP-5 SETUP MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL DVD1 MAIN ADV INPUT SELECT DIGITAL 2-CH ANLG BYP OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD OFF ON OFF The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. COMPONENT OSD SETUP INPUTS DVD1 MAIN ADVANCED COMPONENT OSD ON, OFF Controls the appearance of the on-screen display when the display device is connected to the component video output connector. When set to ON, the display device shows the on-screen display as a 480i video signal on a full blue-screen background. To minimize viewing distractions, the two-line status does not appear on the on-screen display. When set to OFF, the display device does not show the on-screen display, including the two-line status (2-18). Note: When the ON-SCREEN DISPLAY menu BACKGROUND parameter (3-51) is set to OFF, the display device using the component video output connector will not show the on-screen display. 3-23 SETUP ZONE2 IN SETUP INPUTS DVD1 ZONE2 IN JBL Synthesis DIGITAL, ANLG, DMIX Controls the interaction of the digital and analog audio input connectors assigned to the selected Zone 2 input. The INPUT SETUP menu can be used to assign one digital and one analog audio input connector for the selected input. The table shown on the next page describes ZONE2 IN parameter settings. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL DIGITAL ANLG DMIX The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. CAUTION When the ZONE2 IN parameter is set to DIGITAL or ANLG, the SDP-5 recognizes some dts-encoded input sources as audio signals (not data signals) and outputs loud digital noise from the Zone 2 audio output connectors. 3-24 SDP-5 SETUP ZONE2 IN Parameter Settings The table below describes ZONE2 IN parameter settings. DIGITAL The SDP-5 automatically sets the ZONE2 IN parameter to DIGITAL when the ANALOG IN parameter is set to NONE. · The SDP-5 sends the assigned digital audio input connector to the Zone 2 audio output connectors. The DIGITAL IN parameter (3-7) can be used to assign a digital audio input connector for the selected input. ANLG (Analog) DMIX (Downmix) · · The SDP-5 automatically sets the Set the ZONE2 IN parameter to DMIX to send a downmixed version of ZONE2 IN parameter to ANLG Main Zone audio to the Zone 2 audio output connectors. Low-frequency signals lower than the lowest crossover point will be redirected to the subwoofer. If the lowest crossover point is FULL, lowfrequency signals, excluding LFE information, will not be redirected to the subwoofer. Highpass Filter Lowpass Filter dB 0 0 -12 -24 -36 -48 0 0 -60 10 20 50 100 Hz 200 500 1k Highpass filters attenuate low frequencies at 24dB per octave. The curves in the graph above indicate the frequency response of each crossover setting. From left to right, the curves represent crossover settings from 30 to 120Hz. The graph above does not show the THX 80Hz crossover point, which is 12dB per octave. Lowpass filters attenuate high frequencies at 24dB per octave. The curves in the graph above indicate the frequency response of each crossover setting. From left to right, the curves represent crossover settings from 30 to 120Hz. . Custom Speaker Setups continues on page 3-28 3-27 SETUP Custom Speaker Setups (continued from page 3-27) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz C 80Hz M SUB 80Hz 80Hz L SL 80Hz RL 80Hz SR 80Hz RR 80Hz JBL Synthesis CUSTOM SETUP FRONT L/R CENTER SIDE L/R REAR L/R SUBWOOFER THX ULTRA2 SUB BGC ASA 80Hz 40Hz 80Hz 80Hz 80Hz 80Hz OFF N/A APART FRONT L/R SPEAKERS FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz Parameter FRONT L/R CENTER SIDE L/R REAR L/R SUBWOOFER THX ULTRA2 SUB BGC ASA Default Setting 80Hz 80Hz 80Hz 80Hz 80Hz OFF N/A APART Possible Settings FULL, 30 to 120Hz, THX 80Hz FULL, 30 to 120Hz, THX 80Hz, NONE FULL, 30 to 120Hz, THX 80Hz, NONE FULL, 30 to 120Hz, THX 80Hz, NONE FULL, 30 to 120Hz, THX 80Hz, NONE ON, OFF ON, OFF TOGETHER, CLOSE, APART FRONT L/R SETUP SPEAKERS CUSTOM SETUP FULL, 30Hz to 120Hz, THX 80Hz FRONT L/R Opens the FRONT L/R SPEAKERS menu shown above, which can be used to select a crossover point for the Main Zone audio output connectors labeled Front L/R. When set to FULL, the SDP-5 sends a full-range audio output signal to these connectors. Otherwise, the SDP-5 activates a crossover point at the selected setting. Choose the setting closest to the low-frequency rating of the associated speakers. 3-28 SDP-5 SETUP MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz C 80Hz M SUB 80Hz 80Hz L SL 80Hz RL 80Hz SR 80Hz RR 80Hz CUSTOM SETUP FRONT L/R CENTER SIDE L/R REAR L/R SUBWOOFER THX ULTRA2 SUB BGC ASA 80Hz 80Hz 80Hz 80Hz 80Hz OFF N/A APART CENTER SPEAKER FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz NONE CENTER SETUP SPEAKERS FULL, 30Hz to 120Hz, THX 80Hz, NONE CUSTOM SETUP CENTER Note: When the CENTER parameter is set to NONE, center channel signals will not be redirected if the 5. 1a BYPASS listening mode is activated. [. . . ] & (2) 5. 1 ANLG FOR REAR PANEL CFG VOLUME CONTROL SETUP MAIN PWR ON -30dB MUTE LEVEL FULL MUTE ZONE PWR ON -30dB LAST LVL, -80 to +6dB LOCK OPTIONS MODES UNLOCKED AUDIO CNTRL UNLOCKED SETUP UNLOCKED LOCKED UNLOCKED -10dB -20dB -30dB -40dB FULL MUTE SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz C 80Hz M SUB 80Hz 80Hz L SL 80Hz RL 80Hz SR 80Hz RR 80Hz DISPLAY SETUP ON-SCREEN DISPLAY FRONT PANEL DISPLAY A/V SYNC DELAY OFF CUSTOM NAME OFF EDIT CUSTOM NAME ON OFF EDIT CUSTOM NAME SDP-5 ^ W Y BUTTONS TO EDIT UP TO 20 CHARACTERS V BUTTON TO ADVANCE OFF, 1 to 60ms FRONT PANEL DISPLAY STATUS ALWAYS ON BRIGHTNESS 75% 100% 75% 50% 25% ALWAYS ON 2 SECONDS ALWAYS OFF ON-SCREEN DISPLAY STATUS 2 SECONDS POSITION TOP FORMAT NTSC BACKGROUND ON REMOTE STATE ON ON OFF SECAM PAL NTSC TOP CENTER BOTTOM continued on page A-8 A-5 Appendix Menu Tree (continued from page A-5) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX JBL Selecting the SETUP menu INPUTS option prompts the selection of the desired input (e. g. Selecting an input opens the corresponding INPUT SETUP menu shown below. The parameters on the left side of the INPUT SETUP menus are identical regardless of which input is selected. The INPUT SETUP menus shown below indicate default parameter settings for each input. continued from page A-5 DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL SAT INPUT SETUP NAME SAT DIGITAL IN OPTICAL-1 ANALOG IN ANALOG-1 ANLG IN LVL +0dB VIDEO IN S-VIDEO-3 COMPONENT IN 3 2-CH L7 TV %!D 5. 1 L7 TV DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN ANLG TV INPUT SETUP NAME TV DIGITAL IN OPTICAL-2 ANALOG IN ANALOG-3 ANLG IN LVL +0dB VIDEO IN S-VIDEO-5 COMPONENT IN NONE 2-CH L7 TV %!D 5. 1 L7 TV DTS-ES DTS-ES L7 FILMMAIN ADVANCED ZONE2 IN ANLG TUNER INPUT SETUP NAME TUNER DIGITAL IN NONE ANALOG IN ANALOG-4 ANLG IN LVL +0dB VIDEO IN NONE COMPONENT IN NONE 2-CH L7 MUSIC %!D 5. 1 L7 MUSIC DTS-ES DTS-ES L7 MUSIC MAIN ADVANCED ZONE2 IN ANLG DVD2 INPUT SETUP NAME DVD2 DIGITAL IN COAX-2 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-2 COMPONENT IN 2 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL VCR INPUT SETUP NAME VCR DIGITAL IN NONE ANALOG IN ANALOG-2 ANLG IN LVL +0dB VIDEO IN S-VIDEO-4 COMPONENT IN NONE 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN ANLG CD INPUT SETUP NAME CD DIGITAL IN COAX-3 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN COMPOSITE-1 COMPONENT IN NONE 2-CH L7 MUSIC %!D 5. 1 L7 MUSIC DTS-ES DTS-ES L7 MUSIC MAIN ADVANCED ZONE2 IN DIGITAL AUX INPUT SETUP NAME AUX DIGITAL IN OPTICAL-3 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN COMPOSITE-2 COMPONENT IN NONE 2-CH L7 MUSIC %!D 5. 1 L7 MUSIC DTS-ES DTS-ES L7 MUSIC MAIN ADVANCED ZONE2 IN DIGITAL A-6 SDP-5 Appendix MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX continued from page A-6 DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL Selecting an INPUT SETUP menu item opens the corresponding menu shown below. [. . . ]