User manual JBL ON STAGE

[. . . ] The apparatus and AC/DC adapter shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus and AC/DC adapter. TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). PLEASE REFER SERVICING TO QUALIFIED HARMAN CONSUMER GROUP, INC. , SERVICE PERSONNEL. The speaker system does not contain any user-serviceable parts. imporTanT noTe for all elecTronic prodUcTS: Before inserting or unplugging audio cables from the source device's headphones or line-level output jacks, it is good practice to turn off the device first. [. . . ] Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any special accessories needed for compliance must be specified in the instruction manual. MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT UNDER FCC RULES. The normal function of the product may be disturbed by strong electromagnetic interference. compacT deSign The JBL On Stage 400ID loudspeaker dock is a complete 2. 1-channel audio system, in one easy-to-place footprint. digiTal power and dSp The system delivers sound with a powerfully tuned digital audio path. The clean and compact digital amplification, coupled with DSP (digital signal processing) equalization, efficiently provides the transducers with cool-running power. 6 jbl on STage 400id USer gUide Unpacking yoUr jbl on STageTM* 400id Carefully unpack your speaker system and identify all its components: JBL MENU JBL On StageTM* 400ID Adapters for iPod IR remote Power supply Audio cable QUick SeTUp inSTrUcTionS · · · · · Plug the barrel end of the power supply cord into the power jack and plug the other end into the wall. Next, push the power switch; a green LED will light up, indicating that the unit is powered. Find the correct adapter for your iPod, then firmly place it into the docking area shown. Next, place your iPod into the dock, making sure your iPod is firmly seated. Press either button to unmute. Power Jack DC-In Power Switch Power USB Port USB Auxiliary Port Audio-In JBL Power DC-In USB Audio-In www. jbl. com 7 English SpecificaTionS JBL ON STAGETM* 400iD Frequency Response: 40Hz ­ 20kHz Power Consumption: 55 Watts maximum JBL On StageTM* 400ID Transducers: One AtlasTM (45mm) neodymium and four Odyssey® (25mm) Power: 1 x 30 Watts (woofer) 2 x 15 Watts (tweeters), at 1% THD Input Impedance: >10k Ohms Signal-to-Noise Ratio: >85dB Input Sensitivity: 250mV RMS for rated power output Power (USA/Canada): 120 Volts, 60Hz AC Power (Europe/UK): 220 ­ 240 Volts, 50Hz or 60Hz AC Power (Japan): 100 Volts, 50Hz or 60Hz AC Power (Australia): 240 Volts, 50Hz or 60Hz AC UL/CUL/CE-Approved Dimensions: 14-1/4" x 7-3/16" x 3-3/4" (W x D x H) (362mm x 183mm x 95mm) Weight: 3. 8 lb (1. 7kg) Power Supply Manufacturer: JBL, Inc. Power Supply Model: 700-0084 TroUbleSHooTing SOuND QuALiTY Symptom No sound from the JBL On Stage 400ID unit Possible Problem No power to the unit Solution Make sure the wall power outlet or power strip has power. Make sure all switches for the outlet/power strip are on and that all switches for the speaker system are on. Make sure the iPod is properly docked or that the auxilary cable is properly connected to an external audio device. Make sure the iPod or Auxiliary Port In cable is seated all the way into the JBL On Stage 400ID unit. Note Is the LED on? [. . . ] If not, power is not getting to your JBL On Stage 400ID system; try the solutions shown. Incorrect source selection Sound comes from one side/channel only iPod or audio cable is not seated properly If you want to use a longer cable, make sure it's a 3. 5mm mini-jack stereo male-to-male cable Distortion (static, crackling or hissing sounds) Too much bass or treble Noise may be caused by interference from a monitor, cell phone or other transmitting device JBL On Stage 400ID is being overdriven by an amplified audio source. Turn monitor off to see whether noise is eliminated. Make sure that the JBL On Stage 400ID unit is connected to an appropriate source device. Make sure all signal cables are inserted snugly into receptacles. Volume level may be too high Check volume of source device. Some devices will distort the output signal if the volume is set to Maximum. [. . . ]