User manual JBL JBLONSTMALP

[. . . ] Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. [. . . ] This graph illustrates the position at which the current setting falls within the -18 to +12dB parameter range. Press the up and down MENU arrows to increase and decrease the setting in 1dB increments. Press the left MENU arrow to close the graph and return to the RECORD ADV menu. DIG OUT RATE sets the S/PDIF output sampling rate for analog or digital inputs. When set to INPUT, the unit varies the S/PDIF audio output rate to match the sampling rate of the input signal. When set to a numerical value, the output sampling rate remains at the selected value. This is useful for recording devices that operate on a single sampling rate, such as CD-R (44. 1kHz). RECORD (ENABLED, BLOCKED) RECORD prevents feedback loops with recording devices. When set to ENABLED, the unit allows record signals from the selected input to pass to the RECORD AUDIO and VIDEO OUTPUTS. When set to BLOCKED, the RECORD AUDIO OUTPUTS are blocked, preventing feedback loops. However, the unit will still pass video signals to the RECORD VIDEO OUTPUTS. 3-17 The SETUP Menu SPEAKER SETUP CUSTOM SETUP SETUP SPEAKERS CUSTOM SETUP JBL Determining Crossover Settings The CUSTOM SETUP menu allows different crossover points to be set for the following MAIN AUDIO OUTPUTS: FRONT L/R, CENTER, SIDE L/R, REAR L/R, and SUBWOOFER L/R. Crossover points can be set in 10Hz increments within a 30 to 120Hz range. When set to FULL, the unit sends a full-range audio signal to the SIDE L/R outputs. When set to a numerical crossover setting, the unit activates a crossover at the selected frequency. Choose the setting closest to the lowfrequency rating of the side left and right speakers. See pages 3-18 and 3-19 for more information about crossover settings. When set to NONE, the unit redirects side channel signals to the REAR L/R outputs. When both the SIDE L/R and REAR L/R parameters are set to NONE, the unit redirects surround channel signals to the FRONT L/R outputs. The REAR L/R parameter sets the crossover setting for the MAIN AUDIO OUTPUTS labelled REAR L/R. When set to FULL, the unit sends a full-range audio signal to the REAR L/R outputs. When set to a numerical crossover setting, the unit activates a crossover at the selected frequency. Choose the setting closest to the lowfrequency rating of the rear left and right speakers. See pages 3-18 and 3-19 for more information about crossover settings. When set to NONE, the unit redirects rear channel signals to the SIDE L/R outputs. [. . . ] CUSTOM CUSTOM VS PRESET RESET MODE See page 5-17 for more information about the CUSTOM menu. X X X X X X X X X X X X X X -45 CENTER MIX +0dB SURROUND MIX +0dB CNTR DLY SAMPLES +0 MASTER LEVEL +0dB LFE MIX +0. 0dB SUB L/R LVL +0dB CUSTOM 5. 1 BYPASS OUTPUT LEVELS CUSTOM 2CH BYPASS NO PARAMETERS 2CH BYPASS STATUS INPUT MODE INPUT TYPE dB 0 -6 -15 -30 -45 L R 5. 1 BYPASS STATUS INPUT MODE INPUT TYPE dB 0 -6 -15 -30 -45 L C R SL STATUS INPUT MODE CHANNELS ES DECODE SAMPLE RATE dB 0 -6 -15 -30 -45 L C R SL (see page 5-18) 2CH BYPASS BYP (see page 5-19) 5. 1 BYPASS BYP SR LFE (see page 5-20) (see page 5-20) (see page 5-20) (see page 5-20) (see page 5-20) SR SB LFE X X X X X X X X X X X X X X X See pages 5-18 to 5-20 for more information about listening mode STATUS menus. A-11 Appendix INSTALLATION WORKSHEET INPUT SETUP DVD1 NAME DIGITAL IN ANALOG IN ANLG IN LVL VIDEO IN COMPONENT IN 2-CH DOLBY D dts-ES Main Advanced INPUT SELECT ANALOG BYPASS SVIDEO 16:9 SVIDEO 4:3 OSD COMPONENT OSD Zone 2 Advanced INPUT SELECT Record Advanced INPUT SELECT ANLG IN LVL DIGITAL BYPASS DIG OUT RATE RECORD DVD2 LD TV SAT VCR CD PVR GAME TAPE TUNER AUX JBL A-12 SDP-40 SPEAKER SETUP CUSTOM SETUP FRONT L/R CENTER SIDE L/R REAR L/R SUB L/R SUB XOVER LFE OUTPUT LEVEL FRONT LEFT CENTER FRONT RIGHT SIDE RIGHT REAR RIGHT REAR LEFT SIDE LEFT SUB LEFT SUB RIGHT LFE SETTING CAL NOISE L/R LIMITER L/R LIMIT ADJ LFE LIMITER LFE LIMIT ADJ MAIN PWR ON MUTE LEVEL ZONE PWR ON REC PWR ON VOLUME CONTROL SETUP SETTING MONO 80Hz OFF DISTANCE On-Screen STATUS POSITION FORMAT BACKGROUND REMOTE STATE Front Panel STATUS BRIGHTNESS A/V SYNC DELAY CUSTOM CUSTOM NAME BASS TREBLE TILT EQ LOUDNESS BALANCE FADER ZONE2 BALANCE RECORD BALANCE AUDIO CONTROLS SETTING MODES AUDIO CNTRL SETUP SYNTHESIS SETUP 80Hz 80Hz 80Hz DISPLAY SETUP SETTING LOCK OPTIONS SETTING REAR PANEL CONFIG 8 STEREO INPUTS 5 STEREO & 5. 1 ANLG TRIGGER 1 TRIGGER 2 (circle one) TRIGGER SETUP SETTING Appendix A-13 I Index (Standby Button) . . 2-15 Index I-3 SYNTHESIS LIMITED WARRANTY The following JBL Synthesis products are warranted for 2 years from the date of original purchase: Amplifiers, Equalizers, and Surround Sound Processors. Your JBL warranty protects the original owner and all subsequent owners, so long as the original bill of sale is presented when warranty service is requested. Your JBL warranty covers all defects in the material and workmanship with the following specified exceptions: 1. [. . . ]