User manual JBL REF420WHT-H

[. . . ] Although these instructions explain how to install Power Series multielement speakers in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not feel you have the experience, do not attempt the installation yourself, but instead ask your authorized JBL car audio dealer about professional installation options. LOUD MUSIC AND HEARING Playing loud music in an automobile can hinder your ability to hear traffic as well as permanently damage your hearing. [. . . ] LOUD MUSIC AND HEARING Playing loud music in an automobile can hinder your ability to hear traffic as well as permanently damage your hearing. The maximum volume levels achievable with JBL speakers, combined with high power amplification, may exceed safe levels for extended listening. JBL accepts no liability for hearing loss, bodily injury, or property damage as a result of use or misuse of this product. REAR DECK PRECAUTION In some cars, fuel tanks may be located directly beneath the rear deck. Before installation, make sure there is adequate speaker basket clearance before considering this location!ABOUT THE CROSSOVER Except for the P6452, each Power Series multielement speaker includes an outboard crossover for in-line connection to an amplifier which is required for proper operation (see Figure 7 on the next page). The attached crossover wires are keyed and color-coded to aid in correct polarity connections. Mounting the P452, P552, P652, P652s or P953 using the supplied grille. Rotate tweeter so it is angled toward the listener using the UniPivotTM (patent no. Modifying the P452 to be installed in locations requiring fewer than four mounting "ears. " NOTE: Grip the tab (preferably with pliers) and bend to detach it from the speaker. P452/552/652/953 OM 1/27/03 3:36 PM Page 3 INSTALLATION Figure 3. NOTE: The P6452 and P8652 speakers are designed to be installed under factory grilles. NOTE: The positions shown here for the polarities may not resemble the exact connections in every installation. However, in every case, the larger terminal is the positive (+) connection. Tweeter terminals on top Yellow Green Rotate tweeter so it is angled toward the listener using the UniPivotTM (patent no. Mounting the P652 and P652s in 165mm speaker locations. NOTE: The P652 and P652s use an adapter to fit a variety of different 6" openings. Select an appropriate adapter ring and secure it to the vehicle using the sheet-metal screws provided, then attach the speaker to the ring with the machine screws. Woofer terminals on bottom White Blue Red Black P452/552/652/953 OM 1/27/03 3:36 PM Page 4 SPECIFICATIONS Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: P452 4" two-way 4 ohms 50W RMS, 150W Peak 89dB 75Hz ­ 23kHz 2" (51mm) 3-1/2" (89mm) P552 5-1/4" two-way 4 ohms 55W RMS, 165W Peak 89dB 55Hz ­ 23kHz 2-3/16" (56mm) 4-11/16" (120mm) P652 6-1/2" two-way 4 ohms 75W RMS, 225W Peak 90dB 45Hz ­ 23kHz 2-1/4" (58mm) 5-1/16" (129mm) P652s 6-1/2" shallow-mount two-way 4 ohms 55W RMS, 165W Peak 90dB 55Hz ­ 23kHz 1-15/16" (50mm) 5-1/16" (129mm) P953 6" x 9" three-way 4 ohms 110W RMS, 330W Peak 90dB 35Hz ­ 23kHz 3-5/16" (85mm) 8-11/16" x 5-7/8" (221mm x 150mm) P6452 4" x 6" two-way 4 ohms 50W RMS, 150W Peak 89dB 75Hz ­ 23kHz 2-1/16" (53mm) 5-5/8" x 4" (143mm x 102mm) P8652 6" x 8" (and 5" x 7") two-way 4 ohms 75W RMS, 225W Peak 90dB 40Hz ­ 23kHz 2-7/16" (62mm) 7-3/16" x 4-15/16" (183mm x 126mm) GENERAL CARE The loudspeaker grilles may be cleaned with a damp cloth. [. . . ] However, in every case, the larger terminal is the positive (+) connection. Tweeter terminals on top Yellow Green Rotate tweeter so it is angled toward the listener using the UniPivotTM (patent no. Mounting the P652 and P652s in 165mm speaker locations. NOTE: The P652 and P652s use an adapter to fit a variety of different 6" openings. Select an appropriate adapter ring and secure it to the vehicle using the sheet-metal screws provided, then attach the speaker to the ring with the machine screws. Woofer terminals on bottom White Blue Red Black P452/552/652/953 OM 1/27/03 3:36 PM Page 4 SPECIFICATIONS Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: P452 4" two-way 4 ohms 50W RMS, 150W Peak 89dB 75Hz ­ 23kHz 2" (51mm) 3-1/2" (89mm) P552 5-1/4" two-way 4 ohms 55W RMS, 165W Peak 89dB 55Hz ­ 23kHz 2-3/16" (56mm) 4-11/16" (120mm) P652 6-1/2" two-way 4 ohms 75W RMS, 225W Peak 90dB 45Hz ­ 23kHz 2-1/4" (58mm) 5-1/16" (129mm) P652s 6-1/2" shallow-mount two-way 4 ohms 55W RMS, 165W Peak 90dB 55Hz ­ 23kHz 1-15/16" (50mm) 5-1/16" (129mm) P953 6" x 9" three-way 4 ohms 110W RMS, 330W Peak 90dB 35Hz ­ 23kHz 3-5/16" (85mm) 8-11/16" x 5-7/8" (221mm x 150mm) P6452 4" x 6" two-way 4 ohms 50W RMS, 150W Peak 89dB 75Hz ­ 23kHz 2-1/16" (53mm) 5-5/8" x 4" (143mm x 102mm) P8652 6" x 8" (and 5" x 7") two-way 4 ohms 75W RMS, 225W Peak 90dB 40Hz ­ 23kHz 2-7/16" (62mm) 7-3/16" x 4-15/16" (183mm x 126mm) GENERAL CARE The loudspeaker grilles may be cleaned with a damp cloth. [. . . ]