User manual JBL S312 IICH

[. . . ] It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet their needs and expectations. JBL Consumer Products Declaration of Conformity We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the products described in this owner's manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1997 Luc E. 9/01 2 SPEAKER PLACEMENT Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. [. . . ] The hole in the center of each collar is intended for use with banana-type connectors. MODELS: S310II, S312II These models feature four rubber feet that enable them to be placed on a smooth-surfaced floor, such as tile or hardwood. Four metal spikes are supplied for use when the speaker is to be placed on a carpeted surface to decouple the speaker from the floor and prevent unwanted damping. To insert the spikes, gently lay the speaker on its side (not its front or back) on a soft, nonabrasive surface. Each spike screws into the threaded insert in the center of each rubber foot. NEVER drag the speaker to move it, as this will damage the spikes, the feet and/or the wood cabinet itself. CAUTION: Floorstanding (tower) loudspeakers have a high center of gravity and may become unstable and tip over during earthquakes or if rocked, tipped or improperly positioned. If this is a concern, these speakers should be anchored to the wall behind them, using the same procedures and hardware customary for anchoring bookcases and wall units. Customer is responsible for proper installation and proper selection of hardware. MODELS: S26II, S38II The supplied self-adhesive felt pads may be attached to the bottom corners of your speakers to protect your furniture. 4 TROUBLESHOOTING If there is no sound from any of the speakers: · Check that receiver/ amplifier is on and that a source is playing. If there is no sound coming from one speaker: · Check the "Balance" control on your receiver/amplifier. · Check all wires and connections between receiver/amplifier and speakers. · Make sure no wires are touching other wires or terminals and creating a short circuit. · In Dolby* Digital or DTS® mode, make sure that the receiver/processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place, i. e. , the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved, i. e. , the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at www. jbl. com for further information. [. . . ] · Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD player's menu and the DVD disc's menu. 5 S P E C I F I C AT I O N S S26II Description: Maximum Recommended Amplifier Power**: Nominal Impedance: Sensitivity (2. 83V/1m): Frequency Response (­3dB): Crossover Frequency(ies): High-Frequency Transducer: 2-Way 6" bookshelf S38II 3-Way 8" horizontal/vertical, mirror-image bookshelf 175W 8 Ohms 89dB 45Hz ­ 20kHz 800Hz, 3200Hz 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate SpheroidalTM (EOS) waveguide 4" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, shielded; Linear Field ProximityTM (LFP) bezel 8" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, SFGTM magnetic , shorting rings, high-temp oversized Kapton® voice coil, HeatScapeTM motor structure, cast-aluminum baskets, shielded Low Diffraction, IsoPowerTM FreeFlowTM flared Straight-Line Signal PathTM (SSP) All-metal, gold-plated, 5-way binding posts In horizontal configuration: 11-1/2" x 17-1/2" x 11-3/4" 292mm x 445mm x 298mm 28 lb/12. 7kg 150W 8 Ohms 87dB 48Hz ­ 20kHz 2000Hz 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate SpheroidalTM (EOS) waveguide NA Midrange Transducer: Low-Frequency Transducer(s): 6" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, SFGTM magnetic , shorting rings, high-temp oversized Kapton® voice coil, HeatScapeTM motor structure, cast-aluminum baskets, shielded Low Diffraction, IsoPowerTM FreeFlowTM flared Straight-Line Signal PathTM (SSP) All-metal, gold-plated, 5-way binding posts 17" x 9-1/2" x 9-1/2" 432mm x 241mm x 241mm 22 lb/10kg Baffle: Port: Network: Terminals: Dimensions (H x W x D): Weight per Speaker: 6 S310II Description: Maximum Recommended Amplifier Power:** Nominal Impedance: Sensitivity (2. 83V/1m): Frequency Response (­3dB): Crossover Frequencies: High-Frequency Transducer: 3-Way 10" floorstanding 200W 8 Ohms 91dB 37Hz ­ 20kHz 850Hz, 3500Hz 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate SpheroidalTM (EOS) waveguide 4" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, shielded; Linear Field ProximityTM (LFP) bezel 10" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, SFGTM magnetic , shorting rings, high-temp oversized Kapton® voice coil, HeatScapeTM motor structure, cast-aluminum baskets, shielded Low Diffraction, IsoPowerTM FreeFlowTM flared Straight-Line Signal PathTM (SSP) All-metal, gold-plated, 5-way binding posts 38" x 13" x 12-1/2" 965mm x 330mm x 318mm 55 lb/25kg S312II 3-Way 12" floorstanding 250W 8 Ohms 92dB 35Hz ­ 20kHz 750Hz, 3000Hz 1" Pure-titanium dome, with rubber surround, shielded; Elliptical Oblate SpheroidalTM (EOS) waveguide 4" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, shielded; Linear Field ProximityTM (LFP) bezel 12" PolyPlasTM (polymer-coated cellulose fiber) cone, rubber surround, SFGTM magnetic , shorting rings, high-temp oversized Kapton® voice coil, HeatScapeTM motor structure, cast-aluminum baskets, shielded Low Diffraction, IsoPowerTM FreeFlowTM flared Straight-Line Signal PathTM (SSP) All-metal, gold-plated, 5-way binding posts 41" x 14-3/4" x 12-1/4" 1041mm x 375mm x 311mm 77 lb/35kg Midrange Transducer: Low-Frequency Transducer(s): Baffles: Port: Network: Terminals: Dimensions (H x W x D): Weight per Speaker: All features and specifications are subject to change without notice. **The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. We do not recommend sustained operation at these maximum power levels. 7 OWNER'S GUIDE PRODUCT LINE: MODEL NUMBERS: STUDIOTM SERIES PRO SOUND COMES HOMETM JBL Consumer Products 250 Crossways Park Drive, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 800-336-4JBL (4525) (USA only) www. jbl. com ©2001 JBL, Incorporated JBL is a registered trademark of JBL, Incorporated. [. . . ]