User manual JBL S36II

[. . . ] JBL Consumer Products X+ 0+ Y2 0 M HZ X + 0 + Y 2 0 M HZ" X + 0 + Y2 S36II, S36AWII OWNER'S GUIDE PRODUCT LINE: S T U D I OTM S E R I E S D E S I G N G O A L : Bring the thrill of live performance and movie sound to the home environment by calling on JBL's professional engineering leadership. T W E E T E R T Y P E : Pure-titanium dome with EOSTM waveguide W O O F E R T Y P E : Cast-aluminum basket with HeatScapeTM motor structure C R O S S O V E R N E T W O R K : Straight-Line Signal PathTM (SSP) E N C L O S U R E D E S I G N : Sealed P R O F E S S I O N A L R E F E R E N C E : Studio Monitor SPEAKER PLACEMENT Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimal placement of the loudspeakers. [. . . ] Vertical mounting: Use screwholes (1) and (3), or (2) and (4), whichever are uppermost. Supplied Rubber Pad S36AWII top) because it won't be able to lock onto the screw heads. Remember that the JBL logo on the tweeter/mid faceplate can be rotated with choice of speaker position (vertical or horizontal). At least one screw per speaker should be installed in a wooden wall stud. If the special angle-mount screws are not being used, size 10 screws of at least 1-1/2" in length are recommended. If the screws are used in drywall or other surfaces incapable of holding the screw by itself, selection of proper anchors is essential. The customer is solely responsible for proper selection and installation of screws, anchors and other installation hardware. Further installation details are included on the installation template. Installation of Self-Adhesive Rubber Pads: If the speaker is to be placed on a surface (such as a table top or shelf) rather than wall-mounted, the enclosed selfadhesive rubber pads are to be attached to the bottom of the speaker cabinet in their designated recessed locations. If the speaker is to be wallmounted, then the four selfadhesive rubber pads should be attached to the back of the speaker, as shown in the bottom right diagram. When angle-mounting the S36AWII, only two of the rubber pads are required, and they need to be installed on the back of the loudspeaker, near the lower edge, so that they are located between the S36AWII back and the mounting surface. NOTE: The threaded inserts on the bottom of the speakers are to be used only with JBL accessories that have been developed specifically for the S36 and that may become available at a future date. Do not attempt to install bolts or any non-JBL brackets or accessories to these threads, as this might damage the speaker and dislodge the insert. PADS GO HERE For tabletop or shelf placement PLACE RUBBER PADS HERE KEYHOLES FOR MOUNTING HARDWARE For wall-mounting SPEAKER CONNECTIONS CONNECTION TIPS speaker to (­) on the amplifier. Wiring "out of phase" results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material. [. . . ] We do not recommend sustained operation at these maximum power levels. All features and specifications are subject to change without notice. EN 50081-1:1992 EN 50082-1:1997 Luc E. 7/01 OWNER'S GUIDE PRODUCT LINE: MODEL NUMBERS: STUDIO TM SERIES PRO SOUND COMES HOMETM JBL Consumer Products 250 Crossways Park Drive, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 800-336-4JBL (4525) (USA only) www. jbl. com ©2001 JBL, Incorporated. [. . . ]