User manual JBL SCS 200.6 (220-240V)

[. . . ] The SCS200. 6 system is shown here. ® SURROUND CINEMA SPEAKERS SCS200. 5/230 and SCS200. 6/230 OWNER'S GUIDE READ FIRST!Important Safety Precautions! of rubber or plastics may, in seldom cases, react chemically and discolor treated or non-treated wooden surfaces if positioned without protection. Warranty: The following conditions may result in a void product warranty: a. if repairs and/or modifications and/or other treatments/tunings have been carried out by nonauthorized personnel or accessories/supplements are attached, which are not approved by manufacturer/importer. [. . . ] The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. The product should be situated away from heat sources such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat. Avoid installation in extremely hot or cold locations, in an area that is exposed to direct sunlight or near heating equipment. When positioning the product in its final location, make certain that it has adequate ventilation on all sides, as well as on the top and bottom. 3 THANK YOU FOR CHOOSING JBL For more than 50 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We're confident that the JBL system you have chosen will provide every note of enjoyment that you expected ­ and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL. Please take a moment to register your product on our Web site at www. jbl. com. It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet their needs and expectations. JBL Consumer Products INCLUDED One center channel speaker with shelf stand. Five (four in SCS200. 5 system) satellites for left, right and surrounds. Three 6m (20') speaker cables for connection to front, left, center and right speakers, or to subwoofer when speaker-level connections are used (see page 10). Two 4. 6m (15') speaker cables for connection from subwoofer to front speakers, when speaker-level connections are used (see page 10). Three (two in SCS200. 5 system) 12m (40') speaker cables for connection from receiver to rear satellites. Place the subwoofer in that location. 5 MOUNTING OPTIONS SATELLITES AND SURROUNDS On shelves. On the wall. Wall brackets are included. On optional stands. ATTACHING THE SHELF STAND TO THE SPEAKER Prepare the speaker wire as described on page 8. Make sure to preserve the proper polarity (+ and ­ connections) by threading the positive conductor through the hole on + ­ the left, and the negative conductor through the hole on the right looking at the front of the stand. Push down on the red speaker terminal and insert the bare end of the positive wire into the hole under the red cap. Release the cap, and tug Gently pull the slack out of the wire and screw the shelf stand onto the back of the speaker in two places, as shown. gently on the wire to make sure that the connection is snug. Follow the same procedure to connect the negative wire to its terminal. Use the larger screw in the upper screw hole, and the smaller screw in the lower screw hole 6 WALL-MOUNTING Step 5: Tighten the Metal Nut 4 3 2 ¡ with the star washer side between the Metal Nut ¡ 1 8 5 Important Safety Note: The customer is solely responsible for proper selection of mounting hardware not included with the speakers, and for proper assembly and installation of the wall-brackets, including but not limited to the selection of appropriate weight-bearing supports and proper use of the bracket. JBL disclaims any liability for the selection of mounting hardware and/or bracket installation. Be sure to follow these bracket assembly and installation instructions carefully. If you have any questions or doubts about your ability to correctly wall-mount the speakers, consult with your authorized JBL dealer or custom installer. If necessary, use the supplied Metal Bar as a lever by inserting it into one of the holes in the outer edge of the Molded Nut TM. [. . . ] · In Dolby Digital or DTS modes, make sure that the receiver/processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem has followed the speaker, or has remained in the same channel. If the problem is in the same channel, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. [. . . ]