User manual JBL SCS200.5

[. . . ] SURROUND CINEMA SPEAKERS SCS200. 5 ® OWNER'S GUIDE READ FIRST! Important Safety Precautions! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock, do not remove cover (or back). CAUTION: To prevent electric shock, do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 1. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. [. . . ] Since different stands will have different weight capacities and stability characteristics, it is the customer's responsibility to check with the stand manufacturer or dealer to determine whether that specific stand is capable of handling the weight and proportions of these loudspeakers in a safe and stable manner. JBL disclaims any liability for the selection of suitable floor stands and/or correct compatibility between the selected stand and these loudspeakers. The floor stand adapters are compatible with floor stands + ­ equipped with a 1/4"-20 threaded insert. Thread the two conductors through the two holes in the floor stand adapter. Make sure to preserve the proper polarity (+ and ­ connections) by threading the positive conductor through the hole on the left, and the negative conductor through the hole on the right (looking at the front of the adapter). Push down on the red speaker terminal and insert the bare end of the positive wire into the hole under the red cap. Release the cap, and tug gently on the wire to make sure that the connection is snug. Follow the same procedure to connect the negative wire to its terminal. Gently pull the slack out of the wire and screw the adapter + ­ onto the back of the speaker in two places, as shown. Use the larger screw in the upper screw hole, and the smaller screw in the lower screw hole. Screw the floor stand adapter into the floor stand's threaded insert until the speaker is firmly attached to the stand. Back off slightly from the fully tightened position until the speaker is oriented as desired, then rotate the thumbwheel at the bottom of the floor stand adapter to secure the speaker to the stand. 5 WALL-MOUNTING 4 3 2 1 8 5 Important Safety Note: The customer is solely responsible for proper selection of mounting hardware not included with the speakers, and for proper assembly and installation of the wall brackets, including but not limited to the selection of appropriate weight-bearing supports and proper use of the bracket. JBL disclaims any liability for the selection of mounting hardware and/or bracket installation. Be sure to follow these bracket assembly and installation instructions carefully. If you have any questions or doubts about your ability to correctly wallmount the speakers, consult with your authorized JBL dealer or custom installer. If necessary, use the supplied Metal Bar as a lever by inserting it into one of the holes in the outer edge of the Molded Nut TM. Step 2: Firmly grasp the Ball and Shaft £ and pull it straight out of the Attachment Plate ¢. Avoid leaning it to the side for leverage, as this may break off a tab. 6 Step 3: Slide the Molded Nut TM onto the Ball and Shaft £ with the threaded opening facing the ball. Thread the Metal Nut ¡ all the way onto the Ball and Shaft £, with the star washer side away from the ball. Step 9: Once the speaker's orientation has been finalized, insert the Metal Bar into one of the holes in the outer edge of the Molded Nut TM and tighten the Molded Nut TM securely. Keep the Metal Bar in a safe place, in the event that you decide to adjust the speaker's orientation in the future. SPEAKER CONNECTIONS CONNECTION TIPS Separate and strip the ends of the speaker wire, as shown. The wires supplied with the system may already be stripped and tinned for easy insertion into the speaker terminals. [. . . ] · Turn off all electronics and switch the speaker in question with one of the other speakers that are working correctly. Turn everything back on, and determine whether the problem has followed the speaker, or has remained in the same channel. If the problem is in the same channel, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit www. jbl. com. [. . . ]