User manual JBL SCSSAT500

[. . . ] If that is not possible, they may be placed on a wall behind the listening position, facing forward. Experiment with their placement until you hear a diffuse, ambient sound accompanying the mainprogram material heard in the front speakers. The low-frequency material reproduced by the subwoofer is mostly omnidirectional, and this speaker may be placed in a convenient location in the room. However, the best reproduction of bass will be heard when the subwoofer is placed in a corner along the same wall as the front speakers. Experiment with subwoofer placement by temporarily placing the subwoofer in the listening position and moving around the room until the bass reproduction is best. [. . . ] Wall brackets are included. On optional stands (TS 1). Wall-Mounting Thread the wallplate on the base and rotate fully. The brackets should be placed, if possible, so that the screws will fasten into a wooden wall stud. mounting hardware, available through hardware stores, to Place speaker on wall plate. The customer is responsible for proper selection and use of properly and safely wallmount the speakers. SPEAKER CONNECTIONS Connection Tips Separate and strip the ends of the speaker wire as shown. Speakers and electronics terminals have corresponding (+) and (­) terminals. Most manufacturers of speakers and electronics, including JBL, use red to denote the (+) terminal and black for the (­) terminal. It is important to connect all speakers identically: (+) on the speaker to (+) on the amplifier and (­) on the speaker to (­) on the amplifier. Wiring "out of phase" results in thin sound, weak bass and a poor stereo image. With the advent of multichannel surround-sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material. 4 Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS® or other digital processing), where the receiver/processor does not have a subwoofer output, or a volume-controlled preamp (line-) level output: Connect your receiver or amplifier's front left and right speaker terminals to the left and right terminals on the subwoofer that are marked "High Level In. " Connect the left and right terminals on the subwoofer that are marked "High Level Out" to the corresponding terminals on the back of your front left and right speakers. Connect your receiver or amplifier's center, left and right surround-speaker terminals to the corre-sponding terminals on the back of your center, left and right surround speakers. Left Front Center Right Front + ­ + ­ + ­ Subwoofer + OUT IN L HIGH LEVEL ­ ­R + Receiver Left Front Center Right Front + ­ + ­ + ­ Left Surround Right Surround + ­ + ­ Left Surround Right Surround + ­ + ­ 5 ENGLISH Dolby* Pro Logic* (Non-Digital) ­ Speaker Level Dolby Pro Logic (Non-Digital) ­ Line Level Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS® or other digital processing), where the receiver/processor is equipped with a subwoofer output, or a volume-controlled Left Front + ­ ENGLISH preamp (line-) level output: Use RCA-type patch cords to connect the line-level subwoofer outputs on your receiver or amplifier to the linelevel inputs on the subwoofer. Center + ­ Right Front + ­ Subwoofer LineLevel In L R Receiver Left Front Subwoofer Out Right Front + ­ R L + ­ IMPORTANT: Do not use the LFE input on the subwoofer with Dolby Pro Logic processors. Note: If your receiver or amplifier only has one subwoofer output jack, then you will need to use a Y-connector (not included). · Check that the powered subwoofer is plugged in, its Power switch ¡ is switched on to the "ON" position. · Check all wires and connections between receiver/ amplifier and speakers. If there is no sound coming from one speaker: · Check the "Balance" control on your receiver/amplifier. · Check all wires and connections between receiver/ amplifier and speakers. · In Dolby Digital or DTS® modes, make sure that the receiver/processor is configured so that the speaker in question is enabled. If there is no sound from the center speaker: · Check all wires and connections between receiver/ amplifier and speaker. · If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. · If your receiver/processor is set in Dolby Digital or DTS® mode, make sure the receiver/processor is configured so that the center speaker is enabled. If the system plays at low volumes but shuts off as volume is increased: · Check all wires and connections between receiver/ amplifier and speakers. · If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. [. . . ] If there is low (or no) bass output: · Make sure the connections to the left and right "Speaker Inputs" have the correct polarity (+ and ­). · Make sure the subwoofer is plugged into an active electrical outlet. · Make sure the powered subwoofer is plugged in and switched on. · In Dolby Digital or DTS® modes, make sure your receiver/processor is configured so that the subwoofer and LFE output are enabled. [. . . ]