User manual JBL SDP 5

[. . . ] "Dolby, " "Pro Logic, " "Surround EX, " and the double-D symbol are trademarks of Dolby Laboratories. Lucasfilm and THX are trademarks or registered trademarks of Lucasfilm Ltd. 5, 451, 942; 5, 956, 674; 5, 974, 380; 5, 978, 762 and other worldwide patents issued and pending. "DTS, " "DTS-ES Extended Surround, " and "Neo:6" are trademarks of Digital Theater Systems, Inc. [. . . ] · To generate a downmix, the same input must be selected in the · The SDP-5 sends the Main Zone and Zone 2. Otherwise, the Zone 2 audio output assigned analog audio input connectors will mute. connector to the Zone 2 · Main Zone listening mode activation affects the Zone 2 audio audio output connectors. For instance, when the MONO listening mode The SDP-5 ignores the is activated in the Main Zone, the Zone 2 audio output connectors assigned digital audio input will generate mono output signals. · Downmixes cannot be generated when the 5. 1a BYPASS listening · Independent zone monitoring mode is activated in the Main Zone. parameter is set to DMIX, the signals from the Main Zone audio · The ANALOG IN parameter output connectors labeled Front L/R are sent to Zone 2. Signals (3-8) can be used to assign from other Main Zone audio output connectors are ignored. an analog audio input · Independent zone monitoring is NOT available. connector for the selected · It is recommended to set the ZONE2 IN parameter to DMIX when input. recording from a DVD player without built-in Dolby Digital or dts-ES decoding to a VCR or PVR (i. e. · The SDP-5 automatically uses LOGIC7 encoding to downmix multi-channel input sources (except 5. 1-channel analog sources) to LOGIC7-encoded stereo output signals for listening and recording. LOGIC7-encoded downmixes are compatible with matrix decoders, but will sound best when played back through a LOGIC7 listening mode. 3-25 SETUP SPEAKER SETUP SETUP SPEAKERS SPEAKER SETUP JBL Synthesis Selecting the SETUP menu SPEAKERS option opens the SPEAKER SETUP menu shown below, which can be used to configure the Main Zone audio output connectors for the desired speaker setup, set speaker distances, and calibrate output levels. The SDP-5 has eight Main Zone audio output connectors labeled Front L/R, Center, Subwoofer, Side L/R, and Rear L/R. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz C 80Hz M SUB 80Hz 80Hz L SL 80Hz RL 80Hz SR 80Hz RR 80Hz CUSTOM SETUP FRONT L/R CENTER SIDE L/R REAR L/R SUBWOOFER THX ULTRA2 SUB BGC ASA 80Hz 80Hz 80Hz 80Hz 80Hz OFF N/A APART CUSTOM SPEAKER SETUPS SETUP SPEAKERS CUSTOM SETUP Selecting the SPEAKER SETUP menu CUSTOM SETUP option opens the CUSTOM SETUP menu shown above, which can be used to configure the Main Zone audio output connectors for a custom speaker setup. The CUSTOM SETUP menu allows the selection of independent crossover points for each Main Zone audio output connector. Refer to the the paragraph below for more information about determining crossover points. within a 30 to 120Hz range. With the exception of THX 80Hz, all crossover points activate a 24dB-per-octave filter. The graphs on the next page indicate the frequency response of these crossover points. The THX 80Hz crossover point activates a 12dB-per-octave filter for the Main Zone audio output connectors labeled Front L/R, Center, Side L/R, and Rear L/R, and a 24dB-per-octave filter for the Main Zone audio output connector labeled Subwoofer. For each Main Zone audio output connector, select the crossover point closest to the low-frequency rating of the associated speaker. For the output connector labeled Subwoofer, select the crossover point equal to the lowest crossover point of the other speakers. Determining Crossover Points The CUSTOM SETUP menu shown above can be used to assign independent crossover points for each Main Zone audio output connector. Crossover points can be selected in 10Hz increments 3-26 SDP-5 SETUP In general, low frequencies will be redirected from speakers with the highest crossover points to speakers with the lowest crossover points. Low-frequency signals lower than the lowest crossover point will be redirected to the subwoofer. [. . . ] Whenever it appears, any other INPUT SETUP menu shown on the previous page may be substituted. DIGITAL ANLG DMIX DIGITAL ANALOG AUTO DVD1 INPUT NAME EDIT INPUT NAME RESTORE DEFAULT NAME PRESS MENU V TO RESTORE INPUT NAME EDIT INPUT NAME DVD1 ^ W Y BUTTONS TO EDIT UP TO 8 CHARACTERS V BUTTON TO ADVANCE DVD1 ANALOG IN ANALOG-1 ANALOG-2 ANALOG-3 ANALOG-4 ANALOG-5 ANALOG-6 ANALOG-7 ANALOG-8 NONE The appearance of the ANALOG IN menu depends on the configuration of the analog audio input connectors. Refer to page 3-8 for more information. DVD1 VIDEO IN COMPOSITE-1 COMPOSITE-2 COMPOSITE-3 COMPOSITE-4 COMPOSITE-5 S-VIDEO-1 S-VIDEO-2 S-VIDEO-3 S-VIDEO-4 S-VIDEO-5 NONE DVD1 COMPONENT COMPONENT-1 COMPONENT-2 COMPONENT-3 NONE DVD1 DIGITAL IN COAX-1 COAX-2 COAX-3 COAX-4 OPTICAL-1 OPTICAL-2 OPTICAL-3 OPTICAL-4 NONE DVD1 ANLG IN LVL AUTO MANUAL OFF +0dB ON OFF -18 to +12dB AUTO GAIN dB 0 -6 -15 -30 -45 +0. 0dB SL SR SB LFE L C R X X X X X X X Indicates the current amount of analog audio input level adjustment for the selected analog audio input connector. This parameter cannot be adjusted. DVD1 2-CH MODE L7 FILM L7 TV L7 MUSIC L7 MUSIC SURR %!PLII + THX %!PLII MOVIE %!PLII MUSIC %!PRO LOGIC NIGHTCLUB CONCERT HALL CHURCH CATHEDRAL PANORAMA PARTY 2-CHANNEL MONO LOGIC MONO SURROUND MONO USE LAST DVD1 %!D MODE 5. 1 L7 FILM 5. 1 L7 TV 5. 1 L7 MUSIC 5. 1 THX %!DIGITAL 5. 1 2-CHANNEL 5. 1 MONO LOGIC 5. 1 MONO SURR 5. 1 MONO USE LAST DVD1 MAIN ADV* INPUT SELECT DIGITAL 2-CH ANLG BYP OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD OFF ON OFF AUTO OFF Selecting the INPUT SETUP menu MAIN ADVANCED option opens the MAIN ADV menu shown above. The parameters on the left side of this menu are identical regardless of which input is selected. [. . . ]