User manual JBL SP6CS II

[. . . ] MODEL SP6CSII Model SP6CSII has the capability of playing two channels through one loudspeaker, thanks to its dual-tweeter/dualvoice-coil construction. Since the tweeters are close together, in general they should be aimed away from each other for best coverage. For two-channel (stereo) applications, e. g. , as a single speaker in a remote room of a distributed audio system, install the SP6CSII speaker centrally in the ceiling for best stereo imaging, swiveling the tweeters so that one points toward the left and the other toward the right of the listening position, aimed at earlevel height. The SP6CSII may also be used to play the left and right surround channels in a 5. 1-channel home theater system, in which case it should be mounted in the ceiling slightly behind the listening position, centered from left to right and with the tweeters pointing toward the left and right of the listening position, aimed at ear-level height. [. . . ] speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material. To use the push-type speaker terminals, press the red (+) or black (­) cap for the desired terminal, insert the bare end of the speaker wire into the hole below the cap and release the cap. Gently tug on the wire to make sure that it is fully inserted. WIRE LENGTH RECOMMENDED SIZE Up to 20 ft. Greater than 30 ft. 16-gauge 12-gauge 10-gauge INSTALLATION The SoundPoint® Series in-wall speakers were designed to be easily installed. However, if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer. TOOLS NEEDED Pencil Phillips #2 screwdriver Measuring tape Utility knife 4 Carpenter's level Awl EXISTING CONSTRUCTION SP5II, SP6II, SP8II 1/2" 1/2" 1/2" Remove the grille from the speaker frame by pulling on the paper tab. If the tab is missing, to avoid scratching the grille or baffle you may unfold a paper clip, insert the straight end through one of the holes in the grille, and gently pull up. Determine the correct speaker location. Note: Remove the inner template, which is the paint shield, at the perforation. Use the outer template when cutting the drywall. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place. Cut the drywall. Connect the speaker wires to the speaker. The SoundPoint speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grille, gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further. You may also rotate the tweeter to orient the JBL logo as desired. Place the frame assembly in the wall. Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall. Replace the metal grille. 5 EXISTING CONSTRUCTION SP6CII, SP6CSII, SP8CII 1/2" 1/2" 1/2" Remove the grille from the speaker frame by pulling on the paper tab. If the tab is missing, to avoid scratching the grille or baffle you may unfold a paper clip, insert the straight end through one of the holes in the grille, and gently pull up. Determine the correct speaker location. Note: Remove the inner template, which is the paint shield, at the perforation. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place. Connect the speaker wires to the speaker. Model SP6CSII requires two sets of speaker wires, one for each channel. Place the frame assembly in the wall. Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall. The SoundPoint speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grille, gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. [. . . ] · In Dolby Digital or DTS modes, make sure your receiver/ processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/ processor has been enabled. If no subwoofer is being used, make sure the left and right front and rear speakers have been configured as "LARGE. " See your receiver/processor's · Check all wires and connections between receiver/amplifier and speakers. Make sure none of the speaker wires are frayed, cut , punctured or touching each other. [. . . ]