User manual JBL STC-1

[. . . ] ® STC-1 PROGRAMMABLE TOUCH SCREEN REMOTE OWNER'S GUIDE AND PROGRAMMING MANUAL TABLE OF CONTENTS SECTION _________________________________________ PAGE 1. 0 _______________ INTRODUCTION 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 1. 8 Features Important Notes Getting Started The Touch Screen Display The Special Functions Page Battery Recharging and Control Programming the STC-1 Setting the Access Options 4 4 4 5 5 6 6 7 2. 0 ________CREATING AND EDITING PAGES 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 2. 7 Creating a Page Editing a Page Placing Buttons on a Page Using the Text Editor Assigning a Page to a Button Removing a Page Assignment from a Button Deleting a Button from a Page 8 8 9 10 11 11 11 3. 0 ________IR EDITOR 3. 1 3. 2 3. 3 3. 4 3. 5 Menu Options Aligning a Remote Control Sending Infrared Commands to the STC-1 Testing Infrared Commands Editing Infrared Commands 12 13 14 14 14 4. 0 ________MACRO EDITOR 4. 1 4. 2 4. 3 4. 4 4. 5 Menu Options Editing a Macro Inserting an Infrared Command Inserting a Time Delay Macro Hints 15 15 16 16 17 5. 0 ________IR CODE BASICS 5. 1 5. 2 5. 3 5. 4 Frequency Modulation Pulsed IR Codes How the STC-1 Learns IR Commands Hints for Learning IR Codes 18 18 18 19 6. 0 ________PROGRAMMING HINTS 6. 1 Summary: Creating Pages 21 7. 0 ________TROUBLESHOOTING 7. 1 Contacting JBL 22 23 24 25 28 8. 0 ________SPECIFICATIONS APPENDIX A: SCREEN TEMPLATES INDEX WARRANTY UNPACKING AND INSPECTION After unpacking the STC-1, save all of the packing materials in case you ever need to ship the unit. Thoroughly inspect the STC-1 and the packing materials for signs of damage. Report any equipment malfunctions to your dealer. vWARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. vWARNING THIS UNIT CONTAINS NICKEL-CADMIUM BATTERIES. RECYCLE OR DISPOSE OF PROPERLY. Precautions This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] CANCEL This option is used to close the menu without changing functions. EXIT This option is used to exit the infrared editor. OVERLOAD To select a new function, press anywhere on the screen, then display the menu by touching the top of the menu bar (where it says LEARN IR). 12 IR EDITOR 3. 0 Transmit IR Window IR Learning Window 3. 2 Aligning a Remote Control To ensure that a valid signal is being received, all donor remote controls should be properly aligned with the STC-1`s learning window. The STC-1 has an ALIGN IR function to help determine the correct position in front of the learning window. This function is invoked upon entering the Edit IR mode or by selecting ALIGN IR from the pull-down menu while in the Edit IR mode. LEARN IR ALIGN IR To properly align a donor remote control with the STC-1, first make sure the donor remote is at the same height as the learning window. It may be necessary to place the donor remote control on a higher surface than the STC-1. Now press any key on the donor remote control, moving the control back and forth in front of the learning window. The donor remote control is located at the proper distance from the STC-1 when the SIGNAL box is on (darkened) and the OVERLOAD box is off (clear). If the SIGNAL box will not turn on without turning on the Edit IR Menu Bar OVERLOAD box, you should ignore the overload indicator. These special types of commands can usually be learned from any distance as long as the SIGNAL box is on. Touching the display anywhere will cancel the Align IR function. SIGNAL OVERLOAD 13 3. 3 Sending Infrared Commands to the STC-1 Once a donor remote control is properly aligned, the STC-1 is ready to start receiving and storing the infrared commands. First, make sure the STC-1 is in the Edit IR mode and Learn IR is selected from the menu. Next, select a button on the STC-1 that you wish to assign a command to. Now press the key on the donor remote control that transmits the command that you want the STC-1 to learn. After the command has been processed and stored, the STC-1 will display LEARNED. If an error message is displayed, realign the donor remote control and try again. All buttons that have an infrared command assigned to them will have a dashed border displayed around them while in the Edit IR mode. Button with Infrared Command assigned as shown in Edit IR Mode 3. 5 Editing Infrared Commands Most infrared codes will transmit continuously as long as the remote control key is held down. This means that either the entire code or some part of it is being repeated over and over. Some infrared receivers need a command to be repeated a certain number of times to work properly. Also, some infrared receivers may not work properly if the command is repeated at all. This is why the STC-1 allows you to adjust the number of command repeat times and to enable or disable continuous transmission. To edit an infrared command, select EDIT IR from the pull-down menu while in the Edit IR mode. R E P E AT: 03 POWER EDIT IR VOLUME S U S TA I N : OFF ON VCR PAUSE STOP MUTE P L AY > SEARCH REWIND << SEARCH FA S T F W D >> MAIN MENU RECORD 3. 4 Testing Infrared Commands After a command has been learned by the STC-1, you should test it to make sure it behaves properly. [. . . ] Amplifiers, Equalizers, Signal Processing Package, Surround Processor, and Touch Screen Remote--2 Year Warranty. Your JBL warranty protects the original owner and all subsequent owners, so long as the original bill of sale is presented when warranty service is required. Your JBL warranty covers all defects in material and workmanship with the following specified exceptions. These are (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage caused by improper installation or adjustment; (3) damage occurring during shipment (claims must be presented to the carrier); (4) damage to or deterioration of any accessory or decorative surface; (5) damage resulting from failure to follow instructions contained in your owner's manual; (6) damage resulting from the performance of repairs by someone other than an authorized JBL warranty station; (7) any JBL unit on which the serial number has been effaced, modified, or removed; (8) units which have been altered or modified in design, appearance or construction; (9) products sold on an "as-is" or final sale basis. [. . . ]