User manual JBL SYN-K2

[. . . ] Indd 2 04/09/08 16:26:51 FCC STATEMENT AND WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Connect the standard cable for iPod to the rear of the JBL On Time 200ID unit, and every time you dock your iPod, you’ll have a connection for synchronizing. EVERCHARGE TOPOLOGY The JBL On Time 200ID speaker dock charges your iPod, even when it’s not connected to the computer or the system is off. COE (COMPUTER-OPTIMIZED EQUALIZATION) The JBL On Time 200ID system equalization is computer-optimized to provide a rich, complete soundstage. OCT (OPTIMIZED COMPRESSION TOPOLOGY) The JBL On Time 200ID radio and loudspeaker dock utilizes a proprietary compression technology to ensure clean, accurate sound at high output levels. DISPLAY The large, backlit LCD enables easy viewing and menu navigation. Automatic dimming sets the correct brightness level in any room environment. Indd 4 04/09/08 16:26:51 UNPACKING YOUR JBL ON TIME™ 200ID Carefully unpack your speaker system and identify all its components: IR remote FM antenna JBL On Time™ 200ID Adapters for iPod Power supply Audio cable AM antenna QUICK SETUP INSTRUCTIONS • • • • • • Choose the appropriate adapter for iPod and place it into the docking station. For backup memory, install three AAA batteries in the battery compartment underneath the unit. Plug the power adapter into the “DC In” jack and then plug the adapter into a wall outlet. If an additional audio source is used, connect the source to the “Aux In” jack. Press Menu/Up Level at any screen to display Top Menu (may require repeated presses, depending on which menu state the unit was previously in). A single press starts sleep time countdown, using currently set timer. Press and hold for 2 seconds to enter Sleep Timer setting screen (similar to base unit). When iPod is the active source, a single press sends the Play/Pause command to the iPod. When AM, FM or AUX is the active source, a single press mutes audio/amp on the JBL On Time 200ID system. Indd 10 04/09/08 16:26:55 JBL ON TIME™ 200ID MENU TREE Now Playing (ON) Now Playing (Off) Clock Alarm Display Sleep Region 12H 24H HOT KEY POINT (on remote or base unit) AL1-AL7 Brightness Contrast HOT KEY POINT (on remote) HR HR set sleep timer: 15-30-60 A Selection command displays setting confirmation and returns state to Top Level Menu screen. Min Min Select Alarm Set Language: English Spanish French German Italian Dutch am/pm Hr set day Press and hold for 2 sec at any point in menu structure, to return to now Playing screen. ) PRESET HOT KEY POINT (on remote or base unit) SOURCE HOT KEY POINT (on remote or base unit) SNOOZE HOT KEY POINT (hold button for 3 sec on base unit) SNOOZE Preset 1-10 Press and hold Preset button while listening to radio to store current station. Indd 12 04/09/08 16:27:01 SPECIFICATIONS JBL ON TIME™ 200ID Frequency Response: 70Hz – 20kHz Power Consumption: 30 Watts maximum JBL On Time™ 200ID Transducer: Phoenix SE 1-3/4" (45mm) x 2 (full range per channel) Power: 2 x 6 Watts Input Impedance: >5k Ohms Signal-to-Noise Ratio: >80dB Input Sensitivity: 350mV RMS for rated power output Power (USA/Canada): 120 Volts, 60Hz AC Power (Europe/UK): 220 – 230 Volts, 50Hz or 60Hz AC Power (Japan): 100 Volts, 50Hz or 60Hz AC Power (Australia): 240 Volts, 50Hz or 60Hz AC UL/CUL/CE-Approved Dimensions: 11-3/16" x 5-3/4" x 2-3/4" (W x D x H) (284mm x 146mm x 70mm) Weight: 1. 8kg) Remote Battery: CR2025 TROUBLESHOOTING SOUND QUALITY Symptom No sound from the JBL On Time™ 200ID unit Possible Problem No power to the unit Solution Make sure the wall power outlet or power strip has power. Make sure all switches for outlet/ power strip are on and that all switches for speaker system are on. Make sure the correct source is selected; choose FM radio as a source. [. . . ] Tryck på enter för att bekräfta, eller tryck på alarm för att gå direkt till alarm-menyn. En symbol visas till vänster Programmera Välj upp Meny/Upp en nivå Enter Välj ner Vakna upp till din iPod 1. VIKTIGT: Använd endast icke uppladdningsbara alkaliska batterier av typ UM4/AAA/LR3 FELSÖKNING LJUDKVALITET Symptom Det kommer inget ljud från JBL On Time™ 200ID Möjligt problem Ingen ström kopplad till enheten Lösning Se till att det finns spänning i vägguttaget eller elanslutningen. Se till att alla brytare till uttag eller anslutning är påslagna, och att alla brytare på högtalarsystemet är på. [. . . ]