User manual JBL TRIP

[. . . ] If the Bluetooth feature has been turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2). If you have confirmed the Bluetooth feature is on in your phone, pair your phone and headset again (see step 3). If you need more help, contact us at 1-877-MOTOBLU or visit us at www. hellomoto. com/bluetooth and click Support Charge your headset's battery for 2 hours: H500 Bluetooth® Handsfree Headset Get Connected in 4 Quick Steps 1 - CHARGE 2 - START BLUETOOTH FEATURE 3 - PAIR 4 - TEST AND USE Take a moment before you get started to familiarize yourself with your new H500 Handsfree Headset. Earhook Volume Buttons Your phone's Bluetooth feature is off by default. [. . . ] If you need more help, contact us at 1-877-MOTOBLU or visit us at www. hellomoto. com/bluetooth and click Support Charge your headset's battery for 2 hours: H500 Bluetooth® Handsfree Headset Get Connected in 4 Quick Steps 1 - CHARGE 2 - START BLUETOOTH FEATURE 3 - PAIR 4 - TEST AND USE Take a moment before you get started to familiarize yourself with your new H500 Handsfree Headset. Earhook Volume Buttons Your phone's Bluetooth feature is off by default. For most Motorola phones: (Menu) 1 Select M( > Settings > Connection > Bluetooth Link > Setup. 1 Plug the Motorola charger into the end of Call Button the headset. 2 Scroll to Power. Bluetooth feature remains on until you turn it off. Blue Indicator Light The blue indicator light turns on when the battery is charging. When the headset's battery is fully charged (about 2 hours), the blue indicator light turns off. 2 Unplug the charger from the headset. Microphone Note: Headset is not functional while charging. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196 USA www. hellomoto. com 1-877-MOTOBLU 1-800-331-6456 (United States) 1-888-390-6456 (TTY/TDD United States for hearing impaired) 1-800-461-4575 (Canada) Guide Number: 6809494A56-A If you need more help, contact us at 1-877-MOTOBLU. 3 Your Headset PAIR Your Phone Step B - SET THE PHONE TO LOOK FOR YOUR HEADSET For most Motorola phones: (Menu) 1 Select M( > Settings > Connection > PAIR 4 TEST AND USE USING YOUR H500 See Features and Functions Guide on the reverse side of this guide for information on using your H500. Step A - PUT HEADSET IN PAIRING MODE Before you can use your headset, you must pair (link) it with your phone. Call Button Blue Indicator Light Your phone and headset are now paired and ready to make and receive calls. To confirm they are operating properly, make a call: Bluetooth Link > Handsfree > Look for Devices. The phone lists all Bluetooth devices it finds. 2 Press the Call button and the volume button you want to assign as the "volume up" button until the indicator light flashes twice. The headset power turns on. Volume Buttons 2 Gently lift and pull the IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your H500. FOR MORE INFORMATION ON USING YOUR JBL H500 Visit us at www. hellomoto. com/bluetooth and click Support. SUPPORT If you need more help, contact us at 1-877-MOTOBLU. top of the earhook up and off the upper hinge pin. Then, pull it away to remove it. 1 Open Earhook 2 Pull Earhook Up Call Button 3 Flip the headset over. 4 Hook the bottom of the 3 4 Call Button Hinge Pin earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin. MAKING CALLS Function Make a voice dial call End a call Receive a call Reject a call Redial last call Answer a second incoming call Action Tap the Call button and speak the name after the tone Tap the Call button Tap the Call button Press and hold the Call button until you hear a beep Press and hold the Call button until you hear a beep Press and hold the Call button (places first call on hold) MAKING CALLS CONTINUED Function Toggle between two active calls Join a 3-way call Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Disable or enable the indicator light Mute or unmute a call Action Press and hold the Call button Press and hold both Volume buttons Press and hold the Call button until you hear a beep Tap the Call button Press and hold both Volume buttons for 3 to 4 seconds Tap both Volume buttons INDICATOR LIGHTS The indicator light provides information about your headset status. With the Charger Plugged In Headset Indicator Headset Status On (steady) Charging Off Charging complete With No Charger Plugged In Headset Indicator Off On (steady) 10 rapid flashes Slow pulse Quick flash Headset Status Power off Pairing mode Pairing successful Connected (on a call) Standby (not on call) The audio tones provide information about your headset status. Audio Tone Single high tone when pressing volume button Five rapid high tones repeated every 60 sec. [. . . ] 4 Hook the bottom of the 3 4 Call Button Hinge Pin earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin. MAKING CALLS Function Make a voice dial call End a call Receive a call Reject a call Redial last call Answer a second incoming call Action Tap the Call button and speak the name after the tone Tap the Call button Tap the Call button Press and hold the Call button until you hear a beep Press and hold the Call button until you hear a beep Press and hold the Call button (places first call on hold) MAKING CALLS CONTINUED Function Toggle between two active calls Join a 3-way call Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Disable or enable the indicator light Mute or unmute a call Action Press and hold the Call button Press and hold both Volume buttons Press and hold the Call button until you hear a beep Tap the Call button Press and hold both Volume buttons for 3 to 4 seconds Tap both Volume buttons INDICATOR LIGHTS The indicator light provides information about your headset status. With the Charger Plugged In Headset Indicator Headset Status On (steady) Charging Off Charging complete With No Charger Plugged In Headset Indicator Off On (steady) 10 rapid flashes Slow pulse Quick flash Headset Status Power off Pairing mode Pairing successful Connected (on a call) Standby (not on call) The audio tones provide information about your headset status. Audio Tone Single high tone when pressing volume button Five rapid high tones repeated every 60 sec. [. . . ]