User manual JBL WEM-1 (120V)

[. . . ] To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle. The mains plug of the power supply cord shall remain readily operable. Do not expose batteries to excessive heat such as sunshine, fire or the like. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] This LED will light in orange if the local input on the receiver is selected (see page 5 under "Local Input" for more details). Connection Option B Connecting using the speaker-level outputs from your receiver: NOTE: Make sure power is turned off on all components. Connect the speaker wire to the receiver's speaker outputs and the inputs on the transmitter module 8, as shown in Figure 3. Receiver Figure 1. Step 2. Place the receiver module in the desired location in your home near an AC outlet, as it needs to plug into the wall. Connect speaker wire (not included) to the push terminals on the receiver module A and to the connectors on your speakers, as shown in Figure 2. Please note that speaker wire features some form of a polarity indicator to help distinguish its two conductors. Use this polarity indicator to ensure that you are connecting the positive (+) terminal on one speaker to the positive (+) terminal on the other, and the negative (­) to the negative (­). Figure 3. Step 2. Place the receiver module in the desired location in your home near an AC outlet, as it needs to plug into the wall. 4 Step 3. Connect the speaker wire to the push terminals on the receiver module A and the terminals on the rear of your speakers, as shown in Figure 4. Please note that the speaker wire features a polarity indicator to help distinguish its two conductors. Use this polarity indicator to ensure that you are connecting the positive (+) terminal on one speaker to the positive (+) terminal on the other, and the negative (­) to the negative (­). Right Speaker Left Speaker When using the WEM-1 to power surround speakers in a home theater system: In this application, the output level of your WEM-1 will not only be dependent on the volume setting of your A/V source; it will also need to be properly adjusted after installation and before use in order to be able to work correctly with the other speakers in your multichannel surround system. To adjust the output level, turn your A/V source on, set your A/V source's volume control about a third of the way up, and activate the speaker-level-adjustment test tone. Make sure that the WEM-1 transmitter and receiver are on, both of the speakers are connected, and there is RF lock (i. e. , the LED on the receiver is solid green). Using the remote control 1 and 2, adjust the volume level of the WEM-1 until its output level is balanced with the rest of the speakers in your surround system. From this point on, you will not be using the WEM-1 remote control for volume settings. You will be increasing and decreasing the output level for the entire surround sound system using your A/V source's volume control. Please note that the WEM-1 will retain its volume setting when it is in standby, so there is no need to set its volume level every time the system is turned on. Local Input The JBL On Air WEM-1 receiver module also includes a local input on the front of the receiver module. This input allows you to hook up a portable audio player directly to the WEM-1, wherever you may happen to be. For example, you could have the system connected to your audio receiver, listening to a local FM station, and then hook up your portable music player to the local input, switching between the two different sources. Figure 4. Step 4. Plug the transmitter module and receiver module into the wall outlets, using the correct power supplies and power cords. Once the LED on the receiver module lights in solid green, indicating that RF lock has been achieved, verify that there is sound output from the speakers. Then increase and decrease the volume control on your receiver and observe whether this affects the sound output from your speakers. [. . . ] Attach the four included self-adhesive rubber feet in the recesses on the side of the transmitter module. Rotate the JBL logo to a vertical orientation. Remote Control Battery Replacement CAUTION: When replacing the lithium battery in the remote, make sure that the replacement battery is inserted in correct polarity. Place the battery so that its positive (+) side faces up with the tray held so that the surface with the dot and/or with a (+) mark next to the part number is facing up. 2, route de Tours 72500 Château du Loir France Declaration of Conformity declare in own responsibility that the product described in this owner's manual is in compliance with technical Push small tab toward battery slot. Pull battery drawer out. Insert new battery with "+" side up, and slide battery drawer back into remote. standards: EN 55013:2001+A1:2003 EN 55020:2002+A1:2003 EN 61000-3-2:2000 EN 61000-3-3:1995+A1:2001 EN 60065:2002 CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. [. . . ]