User manual JBL WEM-1 ADDENDUM

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] On an A/V or audio receiver, the preamp outputs are usually indicated by RCA-type jacks on the back of the receiver labeled as "pre-out" (please refer to your source's owner's manual to confirm whether it includes preamp outputs). If your source includes these RCA-type outputs, follow the steps in Connection Option A. If your source features only speaker wire outputs, follow steps in Connection Option B. If your receiver does not feature either type of outputs for the front/main channels, it cannot be used with the WEM-1. Connection Option A Connecting using the preamp outputs on your source: NOTE: Make sure the power is turned off on all components. Connect the interconnect cable (included) to the left and right front/main preamp outputs, zone 2 outputs or REC outputs, and the inputs on the transmitter module 7, as shown in Figure 1. Source Front/Main/Second Room Preamp Outputs R L Right Speaker Left Speaker Figure 2. Step 4. Plug the transmitter module and receiver module into the wall outlets, using the power supply and correct power cord. Make sure the ID Code setting on the transmitter 6 is set to the same setting as that on the receiver B. If necessary, configure your receiver to activate the preamp level outputs for the main/front channels (consult your source's owner's manual for specific instructions). When connected properly, the LED on the front of the receiver should be red when first plugged in. When a button on the remote is pressed, the LED should flash green until the transmitter and receiver "lock in. " It will then also light in solid green. When connected properly, the LED on the front of the receiver should be red when first plugged in. When a button on the remote is pressed, the LED should flash green until the transmitter and receiver "lock in. " It will then light in solid green. This LED will light orange if the local input on the receiver is selected (see the "Local Input" section for more details). To connect a portable audio player to the receiver module, simply connect the preamp-out, line-out or headphone jack to the line-in on the front of the receiver module using a 1/8-inch mini-jack ­ 1/8-inch mini-jack cable (not included). To switch between the two sources, push the Input button 3 on the remote control. ID Codes In the unlikely event that you experience interference when operating the system, or if you have more than one set of WEM-1 transmitters and receivers in operation, you may change the channel in which the system operates. On both the transmitter and receiver modules, there is a four-position ID Code selector 6B. The transmitter and receiver must be set to the same position in order for the system to function correctly. You can also set up a maximum of two receiver modules to be receiving from the same transmitter by setting the channel selector on the transmitter and the receiver to the same channel. Please note that the two receiver modules need to be at least 10' (3m) apart, or reception and operating range in one or both units may be degraded. Adjusting the Volume Depending on the type of connection and the specific source that you are using, the volume setting on your audio receiver may affect the sound output level of your WEM-1. Attach the transmitter module with wall bracket to the wall, using two suitable screws (and wall anchors, if necessary). Wall-Mounting the Receiver Module CAUTION: The customer is responsible for proper selection and use of mounting hardware (available through hardware stores), to properly and safely wall-mount the module. Turn receiver module over and remove all four corner screws, as shown in Figure 6. * Blinking stops when unit reaches minimum or maximum volume setting Subwoofer Output The JBL On Air WEM-1 includes a subwoofer output 9 on the receiver module. [. . . ] The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions and other factors, but once per year is the minimum. In the event that your system ever needs service, contact your local JBL dealer or distributor, or visit www. jbl. com for a service center near you. SPECIFICATIONS Frequency Range: (+0dB, ­1dB) Figure 8. 20Hz ­ 20kHz 50 Watts per channel 80dBA Up to 70' (22m), depending upon conditions 2. 4GHz 100V ­ 240V AC, 50/60Hz Amplifier Output: Signal-to-Noise Ratio: Operating Range: RF Operating Frequency: Power Requirement: Dimensions Transmitter Module: (H x W x D) Receiver Module: (H x W x D) Weight Transmitter Module: Step 2. Rest the receiver module on top of the stand and reattach the two screws that were removed in Step 1 through the holes in the stand into the bottom of the receiver module, as shown in Figure 9. 1-1/8" x 6" x 3-7/8" (29mm x 154mm x 98mm) 3-3/4" (95mm) high with antenna extended 1-1/8" x 6-3/16" x 4-5/8" (29mm x 158mm x 116mm) 3-3/4" (95mm) high with antenna extended 0. 6 lb (0. 3kg) 0. 9 lb (0. 4kg) Figure 9. Receiver Module: Step 3. Rotate the JBL logo 90° by gently pulling it out and turning it. Features, specifications and appearance are subject to change without notice. Vertically Mounting the Transmitter Module Step 1. [. . . ]