User manual JENSEN CD-470C DATASHEET
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JENSEN CD-470C. We hope that this JENSEN CD-470C user guide will be useful to you.
Manual abstract: user guide JENSEN CD-470CDATASHEET
Detailed instructions for use are in the User's Guide.
[. . . ] Mount sleeve after wiring.
3) Follow the wiring diagram carefully and make certain all connections of the wiring harness are properly secured and insulated to insure proper operation of this unit. After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be "on"). If unit does not operate, recheck all wiring until the problem is corrected. Once proper operation is achieved, turn off ignition switch and proceed with final mounting of the chassis.
4) Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. [. . . ] The unit will enter the general configuration menu and display CL-24 or CL-12. To select 12 hour clock operation, press the up tuning button once or until CL-12 is displayed. If 24-hour clock operation is desired, press the up tuning button until CL-24 is displayed. To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds).
Configuration of Auxiliary Low-Level Audio Input
Press AUDIO ADJUST for more than three seconds. To configure the radio to accept low-level audio signal, scroll through menu items until "AUX--**" (where ** can equal Y or N) is displayed. To disable this feature, use the up tuning button to change back to "AUX-N". To exit, press AUDIO ADJUST again or the configuration menu time out (takes about five seconds). Note: If this feature is disabled, the front panel jack will also be disabled.
2
JHD1000 Wiring
Low 530 87. 9 5900 531 87. 50 144 6200 1629 108. 00 288 1629 108. 0 1629 90. 0 1600 108. 0 1620 107. 9
SEE PAGE 4 FOR LOW LEVEL AUDIO INPUT DIN CONNECTOR
Configuration (continued)
High 1710 107. 9 5kHz 9kHz 50kHz 9kHz 9kHz 100kHz 9kHz 100kHz 10kHz 100kHz 10kHz 200kHz 9kHz 50kZHz
From 9-Pin Harness 2-Bond Pair
PINK (TRIGGER) - SEE CHART C
Country Code 10kHz 200kHz
Country
Band
Step
The wiring diagram depicts all the wiring connections required for proper operation of the unit.
11
North America
AM FM
12
Europe
SW AM FM LW 531 87. 5 522 76. 0 530 88. 0 530 87. 9 531 87. 5 1602 108. 0
13
Pacific
AM FM
14
Japan
AM FM
15
Latin America
AM FM
TO ANTENNA
16
Brazil
AM FM
Wiring Color Codes
2-Bond Pair
21
Saudi Arabia
AM FM
Configuration of the World Band Tuner
*SPEAKER WIRES ARE BONDED PAIRS NEGATIVE GRAY WIRES PAIRED WITH RESPECTIVE POSITIVES *SOLDER AND TAPE ALL SPLICES 9 PIN CABLE CONNECTOR BLACK/WHITE (GROUND) GREEN/WHITE (BATTERY +12V) - SEE CHART A ORANGE/WHITE (ACC. +12V) - SEE CHART B 4 PIN CABLE CONNECTOR
Press AUDIO ADJUST for more than three seconds. "CC--**" will appear on the display (where ** can equal 11, 12, 14, 15, 16 or 21). Use the up tuning button to select the proper country code for the region of interest. Press the down tuning button (6b) to adjust the hours or the up tuning button (6c) to adjust the minutes. "A" or "P" will appear on the display to indicate AM or PM. When no adjustment is made for five seconds, the time will be set and normal operation will resume.
5. Sound Adjustment
Press AUDIO ADJUST (5) repeatedly to step through the following sound adjustment options: Bass, Treble, Balance (left to right) and Fader (front to rear). When the desired option appears in the display, rotate the volume control knob to adjust that audio feature. When no adjustments have been made for five seconds, the unit will resume normal operation.
Press the alarm button momentarily to turn the alarm function on or off. The bell symbol will appear in the display when the alarm function is on. To check the time for which the alarm is set, press the alarm button for more than one second, and the time will flash in the display. After five seconds, the display will stop flashing and the unit will return to normal operation. Note: When the alarm feature is activated, the unit will turn on even if the ignition is off. The mode of operation (radio or auxiliary input) and volume level that were last used will be automatically recalled. [. . . ] If your media player does not include an audio out cabled, use the Aux Cable included with this unit.
Basic Operation
5 2
JHD1000
1&4
3
PUSH POWER
AUDIO
MODE
ADJUST
6a
AUX IN
T /
F
HEAVY DUTY
TUNE
BAND
TUNE
1 6
2 4 5
3
6b
6c
7
8
4
JHD1000
12. Preset Stations
Six numbered preset buttons (12) store and recall stations for each band.
Radio Operation
Store a Station
9. The current station will be stored, and the corresponding preset number will appear in the display.
Press BAND (9) to change between two FM bands (FM1 and FM2), one AM band (AM) and the weather band (WTHR). When an FM stereo broadcase is being received, the ST indication will appear in the display. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JENSEN CD-470C
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JENSEN CD-470C will begin.