User manual JENSEN CDMP-40 DATASHEET

[. . . ] 4 Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Tuner Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 CD/MP3 Player Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Satellite Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Treble Level Use the rotary encoder (1) to adjust the Treble level range from "-6" to "+6". Balance Use the rotary encoder (1) to adjust the Balance between the left and right speakers from "12L" (full left) to "12R" (full right). Fader Use the rotary encoder (1) to adjust the Fader between the rear and front speakers from "12R" (full rear) to "12F" (full front). POWER Volume Control To increase the volume, turn the rotary encoder (1) to the right. While adjusting the volume, the LCD displays a bar graph and numerical representation of the level. The maximum volume setting is 40. Mute Press the MUTE button (16) to mute the audio output. Press MUTE again to restore the audio output to the previous level. Mode Press the MODE button (4) to select a different mode of operation, as indicated on the display panel. Available modes include Tuner (AM/FM), SAT (Sirius) radio, CD, iPod and AUX in (optional Auxiliary Input). 5 JHD3510 System Menu 1. · · · · · · · · · · · · · · Press and hold the AUDIO/MENU button (3) for more than 2 seconds to enter the system menu. The first menu item, "Beep Tone", will appear on the display. Press the AUDIO/MENU button repeatedly to navigate the system menu and select the desired item. Beep Tone (ON/OFF): Turn the audible beep ON/OFF (heard when functions/buttons are selected). Use the rotary encoder knob (1) to move through the list of available categories and select the program type you wish to search. After selecting the desired PTY, press and hold the TUNE/SEEK >>| or |<< button (19, 18) to search the band for broadcasts of this type. NOTE: Performing a PTY search on "ANY" will Seek Tune and stop on any station broadcasting RBDS, regardless of the program type. 7 JHD3510 Weather Band Operation What is the NOAA Weather Radio/Weatheradio Canada?This is a nationwide system that broadcasts local weather emergency information 24 hours a day. network has more than 530 stations covering the 50 states as well as the adjacent costal waters, Puerto Rico, the U. S. Each local area has its own transmitting station and there are a total of seven broadcasting frequencies used. A similar system is available in Canada under the Weatheradio Canada service administered by Environment Canada. Tuning to Weatherband Press and hold the BAND/WB button (15) to access the Weatherband. The indication "WB" will appear on the display panel, along with the current number and channel indication: "CH01", CH02", "CH03", "CH04", "CH05", "CH06" or "CH07". Use the TUNE/SEEK >>| or |<< buttons (19, 18) to tune to each of the seven channels until you find the weatherband station broadcasting in your area. Since the broadcasts are local weather and information, the transmission power is usually very low (much less than standard AM or FM stations) so you will usually receive only one station unless you are on the edge of two or more broadcast signals. Depending on where you are located, there is a possibility you will receive only a very weak signal or none at all. [. . . ] Random Play During playback, press the 4/RDM button (7) to play all songs in the current category in random order. Selecting Tracks NOTE: iPod and iPod Cable sold separately. Accessing iPod Mode To enter iPod mode from any other source, press the MODE button (4) until "iPod" appears on the display. 8 Din iPod Ready Cable Turning the iPod On/Off The iPod power turns on automatically when an iPod is connected to the 30-pin iPod cable, as long as the vehicle ignition is turned on. You can turn the iPod off by disconnecting it from the cable or by turning the ignition off. When the ignition is turned off, the iPod will pause and then enter sleep mode after 2 minutes. [. . . ]