User manual KATHREIN UFE 370

[. . . ] 20210052 2 Preface Preface Dear customer, This Operating Manual is intended to help you make the fullest use of the extensive range of functions offered by your new DVB-T receiver. We have tried to make the operating instructions as easy as possible to understand, and to keep them as concise as possible. If you will not be using your receiver for a longer period, you should therefore use the power switch to disconnect it from the power supply to save energy. For shorter breaks, you can switch the receiver to standby on the remote control, which uses only a minimal amount of energy. [. . . ] Electronic equipment is not household waste - in accordance with directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27th January 2003 on used electrical and electronic equipment, it must be disposed of properly. At the end of its service life, take this unit for disposal at a designated public collection point. 8 Safety Instructions Safety Instructions 9 Operation Operation First Installation Once you have connected up your receiver in the correct way, turn it on at the power switch on the rear of the unit. The following screen appears: Select the menu language you want using the / buttons. the BZD 30 from Kathrein), the antenna will need a 5 V supply (only if the antenna does not have its own power supply). The receiver then jumps automatically to the channel search menu and start autoscanning the complete frequency range. The channels found by the receiver are stored in the preset channel list. You can then use the / buttons as usual to switch between the channels. 10 Operation Channel Selection (TV and Radio) The receiver is shipped with the most popular channels programmed in to it. If you press the red button while the current programme is running, you are switched to "Advanced mode". You can still view the programme in the background. Audio Press the Audio button to view the sound mode (TV or radio) being broadcast over the receiving channel. If the channel is not transmitting language information the receiver shows «Unknown». Switch between Left/Right/Stereo sound using the SOUND button. Pause and Zoom With these buttons, the picture can be reduced in size or frozen. 14 Operation The Quality Button (Antenna Adjustment Help Function) In addition to displaying the reception strength and quality, the receiver also features an audible-signal help function to aid in adjusting the antenna: Adjust the receiver to the channel you want to receive and press the Quality button. As soon as the Quality display is activated, the receiver starts transmitting an audio signal at a frequency and repetition rate corresponding to the received signal. 15 Main menu Main menu Accessing the Main Menu (MENU Button) Press the MENU button to access the main menu. Select the submenu you want and press the OK button. Five submenus are available, as detailed below: 1) Timer Menu for preset programme recording or for automatic stop 2) Edit Channel List Sort, edit and delete channels 3) Edit Favourite List Organise channels (save, sort, edit and move) 4) Installation Menus to set up the antenna, the channels, the system menu and the parental control 5) Game Two games are available 16 Main menu Timer Setting (Automatic Programming) Note: The timer can be programmed either by way of the EPG (Electronic Programme Guide; see page 14) or as follows: The clock must be correctly set so the timer is ready for programming (see "Installation Menu/System Setup/Setting the Time"). Programme the event number (1 to 8), and activate the timer to enable programming. To select the date, press the OK button while in the "Date" field. A calendar appears, and you can then select the desired date using the / / buttons. => Alternatively: Move to the date field, select the day, month and year using the / buttons and key in the desired number using the number pad. Then select the start and end times and the number of the channel you want to record. To select the channel, press the OK button while in the "Channel" field. The channel list appears, and you can then select the channel you want using the / buttons. Press OK to confirm your selection and programme it into the timer. 17 Main menu Organising Channels and Favourites Sort: 1. Choose "Edit Channel List" and press "OK" to confirm. [. . . ] The internal clock is set as follows: a) Apply the broadcast time (default). In this case the time difference between GMT and the location (in Germany + 2 hours in Summer, + 1 hour in Winter) must be allowed for. b) If you select «Off» in the first field, you will need to enter the time and date manually using the number pad. Note: It may be that some channels do not transmit the correct GMT time. [. . . ]