User manual KENWOOD DDX8036BT

[. . . ] (Refer to the Instruction Manual. ) . . . . . . . . . . 1 2 0 . . . . . . . . . . 6 . . . . . . . . . . 1 3 ! . . . . . . . . . . 1 . . . . . . . . . . 1 4 @ . . . . . . . . . . 1 2WARNING • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse. . . . . . . . . . . 1 5 . . . . . . . . . . 1 . . . . . . . . . . 2 6 About the Front Panel When removing the product from the box or installing it, the front panel may be positioned at the angle shown in (Fig. [. . . ] • Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car. • When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do • • • • not connect the - connector to a rear output terminal. After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. This unit has the cooling fan (page 5) to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction. Do not press hard on the panel surface when installing the unit to the vehicle. Reception may drop if there are metal objects near the Bluetooth antenna. Bluetooth antenna unit ¤ CAUTION Install this unit in the console of your vehicle. Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot. English 3    FFPKJUKNIP'A/AA$ Connection Ignition key switch ACC Ignition wire (Red) Battery wire (Yellow) Car fuse box (Main fuse) Car fuse box Antenna Cord Ground wire (Black) (To car chassis) ignition (red) and battery wire (yellow) ¤ If you connect the(ground), wire may causetheshort circuit, that in to the car chassis you a turn may start a fire. Always connect those wires to the power source running through the fuse box. A A FM/AM antenna input Battery ⁄ Connect to the vehicle's parking brake detection switch harness. Parking sensor wire (Light Green) PRK SW For the sake of safety, be sure to connect the parking sensor. Connect to vehicle's reverse lamp harness when using the optional rear view camera. To steering remote ⁄ To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. To car light control switch Connect to the terminal that is grounded when either the telephone rings or during conversation. ⁄ To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. When using the optional power amplifier, connect to its power control terminal. ⁄ 4 DDX SERIES If no connections are made, do not let the cable come out from the tab.    FFPKJUKNIP'A/AA$ Bluetooth Microphone (Accessory !) (see page 8) Cooling fan FUSE (15A ) Accessory 1 Reverse sensor wire (Purple/White) REVERSE To front left speaker White/Black White + Steering remote control input (Light Blue/Yellow) REMOTE CONT STEERING WHEEL REMOTE INPUT To front right speaker Gray/Black Gray + Dimmer control wire (Orange/White) ILLUMI Mute control wire (Brown) MUTE To rear left speaker Green/Black Green + Motor antenna control wire (Blue) ANT. CONT Power control wire (Blue/White) P. CONT To rear right speaker Purple/Black Purple + English 5    FFPKJUKNIP'A/AA$ System Connection iPod (commercially available) iPod USB terminal USB device (commercially available) Audio input (iPod/AV Input 3 switchable) Resistance-free stereo type mini plug (3. 5φ) Visual input (iPod/AV Input 3 switchable) Resistance-free mini plug (3. 5φ) Accessory 3 Accessory 4 AV OUT Accessory 2 AV IN1 To Camera control terminal (Green/Red) Audio/Visual Output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) Audio/Visual Input • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) Audio/Visual Input • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) Rear View Camera Input • Visual input (Yellow) Front Preout • Audio left output (White) • Audio right output (Red) Rear Preout • Audio left output (White) • Audio right output (Red) Subwoofer Preout • Audio left output (White) • Audio right output (Red) Center Preout (Green/White) To Relay Box RELAY 1 RELAY 2 (Blue/Red) (Blue/Red) 6 DDX SERIES CENTER SUB WOOFER REAR FRONT REAR VIEW CAMERA AV IN 2    FFPKJUKNIP'A/AA$ Optional Accessory Connection iPod (commercially available) KCA-iP301V (Optional Accessory) Visual Output (Yellow) Audio Output (Black) USB terminal USB terminal USB device (commercially available) iPod TV Tuner (Optional Accessory) Navigation System (Optional Accessory) Connection cable (Included in the Navigation System) Connection cable (Included in the TV tuner)   TO MONITOR UNIT ⁄ Navigation units that can be connected to this unit. [. . . ] Lower the frame and pull it forward as shown in the figure. Accessory 5 Removing the Unit 1. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. Insert the two removal tools 5 deeply into the slots on each side, as shown. Accessory 5 Catch Lock ⁄ • The frame can be removed from the top side in the same manner. 3. Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. 2. [. . . ]