User manual KENWOOD KAC-648
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KENWOOD KAC-648. We hope that this KENWOOD KAC-648 user guide will be useful to you.
Manual abstract: user guide KENWOOD KAC-648
Detailed instructions for use are in the User's Guide.
[. . . ] 2CAUTION Do not wipe the panel with a hard cloth or a cloth dampened by volatile solvents such as paint thinner and alcohol. They can scratch the surface of the panel and/or cause the indicator letters to peel off.
Accessories
Part name
Round terminal (Large) Round terminal (Medium) Round terminal (Small) Terminal cover (Power terminal) Self-tapping screws (ø4 × 16 mm)
External View
Number of Items
1 2 1 1 4
Protection function
This unit is equipped with a protection function for protecting this unit and your speakers from various accidents or problems that can occur. When the protection function is triggered, the Power indicator goes off and the amplifier stops operating.
s Power indicator:
When the power is turned on, the Power indicator lights. [. . . ] · The installation to the vehicle should securely fasten the unit to a place in which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident. · After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally.
3
Controls
This is a 4 channel amplifier including 2 stereo amplifiers in a body. One amplifier is referred to as amplifier A and the other is amplifier B. This unit is compatible with a large variety of systems by combining the switches and functions described in the following.
5
SPEAKER LEVEL INPUT LEFT RIGHT A SPEAKER LEVEL INPUT A B B B L R
FUSE(25A) BATT
POWER IN
SPEAKER OUTPUT
BRIDGED
GND
25
LEFT
RIGHT
A P. CON(REMOTE)
1
234 8
6 90!
7
FILTER
OPERATION
MONO(Lch) 1. 0
OFF STEREO HPF LPF
INPUT SELECTOR AB A
0. 5
LINE IN A B
LINE OUT A+B
1. 0
OPERATION
STEREO (Lch) MONO
FILTER
OFF HPF LPF
MONO L
L
GND
0. 3 MIN MAX MIN
0. 5 0. 3 MAX
INPUT SENSITIVITY(V) CONTROL A
R
R
INPUT SENSITIVITY(V) CONTROL B
4 CHANNEL POWER AMPLIFIER
mA
@ # $ %
mA
1 Fuse (25 A × 1) 2 Battery terminal 3 Ground terminal 4 Power control (REMOTE) terminal 5 Amplifier A speaker output terminals 6 Amplifier B speaker output terminals ySPEAKER OUTPUT terminals · Stereo Connections:
When you wish to use the unit as a stereo amplifier, stereo connections are used. The speakers to be connected should have an impedance of 2 or greater. When multiple speakers are to be connected, ensure that the combined impedance is 2 or greater for each channel.
When multiple speakers are to be connected, ensure that the combined impedance is 4 or greater. 2CAUTION The rated input of the speakers should be no less than the maximum output of the amplifier. Otherwise malfunction may result.
7 Speaker level input terminals 8 INPUT SELECTOR switch
This switch selects the input method of the signals to be amplified by amplifiers A and B.
AB A INPUT SELECTOR
· A B position:
Amplifies both of the signals input to amplifiers A and B.
· Bridged Connections:
When you wish to use the unit as a highoutput monaural amplifier, bridged connections are used. (Make connections to the LEFT channel (+) and the RIGHT channel () SPEAKER OUTPUT terminals. ) The speakers to be connected should have an impedance of 4 or greater.
· A position:
Amplifies only signal input amplifier A with both amplifiers A and B.
9 Amplifier A LINE IN terminal 0 Amplifier B LINE IN terminal
4
!LINE OUT terminal
These jacks output respectively the signals input to amplifiers A and B. They always output the stereo signals regardless of the position of the OPERATION switch.
independently according to the setting of this switch.
· STEREO position:
The amplifier can be used as a stereo amplifier.
@ RCA cable ground lead terminal # INPUT SENSITIVITY control
Set this control according to the pre-output level of the center unit connected with this unit, or to the maximum power output of the genuine-accessory car stereo. The sensitivities of amplifiers A and B can be adjusted independently regardless of the position of the input selector switch. Use the diagram on 15 10 1. 0 the right as a guide.
1. 0
· MONO (Lch) position:
Amplifies the signal input from the left side only. Set to this position and make bridged connections to use as a high-power monaural amplifier. (The input right signal is not output. )
% FILTER switch
These switches allow filtering of the speaker output signals.
· HPF(High Pass Filter) position:
Only frequencies of 150Hz or higher are output. [. . . ] (No sound from one side. )
POSSIBLE CAUSE
SOLUTION
· Input (or output) cables are · Connect the input (or output) disconnected. · Protection circuit may be · Check connections by referring activated. · The fuse may be blown because · Replace the fuse with a new the volume was too high. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KENWOOD KAC-648
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KENWOOD KAC-648 will begin.