User manual KENWOOD KDC-C710

[. . . ] Take the following precautions to avoid damage to the compact discs. · Avoid touching the recorded side (the side without the titles on) when you hold a compact disc. · The reflective film on a CD-R or a CD-RW is more fragile than that on an ordinary music CD, and may peel off if scratched. Fingerprints on a CD-R or CD-RW are also more likely to cause skipping when the disc is played. [. . . ] Detailed handling instructions will appear on the CD-R or CD-RW package: read this information carefully before using the disc. · Do not store discs where they will be exposed to direct sunlight (such as on the seat and dashboard) or high heat. A CD-R or CD-RW is more susceptible than a music CD to damage from high temperatures and humidity, and in some cases, may become unusable if left in the car for long periods of time. · If you do not use your unit for an extended time, remove the discs from the unit and put them in their cases. Do not leave them lying around without cases, piled up, or leaning on a wall and so on. · If you attach an adapter to an 8 cm (3") compact disc and load it into this unit, the adapter may be detached from the disc, causing damage to the unit. Do not use 8 cm (3") compact discs. CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is using laser beams that are of a weaker class. 2WARNING Take the following precautions to prevent fire and avoid personal injury : · Check that no metal objects (coins, tools, etc. ) are left inside the unit to avoid short circuits. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO THIS UNIT AND CONTROL UNIT. · The disc name preset function can register names of up to 100 discs using up to 12 characters for each disc name. The availability of this function as well as the number of discs which can be registered using this function and the number of usable characters may be variable depending on the control unit in use. 2CAUTION · Do not connect the changer control cable while the control unit is turned ON. · Do not install an antenna of radio equipment or distribute the antenna cable near the changer output cable, for this could cause malfunction with this unit. Setting the O-N switch Set the O-N switch (lying to the right of the EJECT key) depending on the unit connected, as follows: Control unit CD text-capable Not CD text-capable Changer switching None KCA-S210A None KCA-S210A KCA-S200 unit O-N switch setting N N O O O Consult the instruction manual for your control unit to check whether or not it is CD text capable. That information can be found on the page for External Disc Control in the section concerning switching to "N. " Loading compact discs 1 Projection ' Installation 4 Accessories A×1 B×4 C×4 D×1 E×1 ' ' Removing the transportation screws Make sure the disc magazine is the right way up with the "disc" logo on the top. Pull the tray out by the projection. ' Insert the magazine into the CD changer until it clicks. Remove all 3 transportation screws for protecting the internal mechanism before you start to install the unit. NOTE After removing the transport screw, retain it carefully and attach it again before transporting the unit again. Transportation screws 2 ' 5 Angle adjustment switches Tray Close the CD changer door. Left side Angle adjustment switches 45 90 0 0 45 90 NOTE Place the disc on the tray with the label facing upwards. 2CAUTION · Take care to insert trays into the correct grooves in the disc magazine and to insert discs properly into the tray grooves. [. . . ] 2CAUTION · Take care to insert trays into the correct grooves in the disc magazine and to insert discs properly into the tray grooves. Use the CD changer with its door closed to prevent the entry of dust into the changer. 6 Right side Magazine ejection Installation angle "EJECT" Angle adjustment switch position 90 · The angle adjustment switches on the both side of the unit are to be set according to the angle of installation of the CD auto changer. If the switches are not set properly, sound skip or other malfunction may occur. [. . . ]