User manual KENWOOD KRF-V8010D

[. . . ] AUDIO VIDEO SURROUND RECEIVER Preparation Remote Control Other Operations KRF-V8010D INSTRUCTION MANUAL KENWOOD CORPORATION About the supplied remote control . . Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). [. . . ] If a graphic equalizer is connected, the MONITOR key should be left in the on position. Alternately, if a cassette deck equipped with a 3-head system is connected to the MONITOR jacks, you will be able to monitor the just-recorded signal while making recordings on the cassette deck. By switching the MONITOR key on and off, you can compare the sound of the source signal and the just-recorded signal. For more information, refer to the instruction manual of the connected component. · If you turn off all of the speakers when in the surround mode, the mode is cancelled as well, resulting in stereo playback. 2 Connect headphones to the PHONES jack. 3 Use the VOLUME CONTROL (VOLUME) to adjust the volume. Recording video 1 Use the input selector to select the video source (other than "VIDEO1") you want to record. To adjust the balance Use the test tone feature. 3 Start playback, then start recording. Operations · Either press the LISTEN MODE, SOUND, and SETUP keys, or switch to another input source to cancel SOURCE DIRECT playback. STEREO MONITOR ST. Listening to radio broadcasts KRF-V8010D (En/T) 18 Tuning (non RDS) radio stations Radio stations can be classified into RDS (Radio Data System) stations and other stations. To listen to or store RDS stations in the preset memory, see the section entitled, "Using RDS". Using RDS (Radio Data System) RDS is a system that transmits useful information (in the form of digital data) for FM broadcasts along with the broadcast signal. Tuners and receivers designed for RDS reception can extract the information from the broadcast signal for use with various functions, such as automatic display of the station name. AUTO BAND RDS functions: PTY (Program Type Identification) Search ) Automatically tunes to a station that is currently broadcasting the specified program type (genre). MULTI CONTROL INPUT SELECTOR EON (Enhanced Other Network) reservation ¡ Sets the tuner to automatically switch to stations broadcasting one of two types of programs, even though you are listening to another station. The tuner returns to the original station when the broadcast of the selected program ends. PS (Program Service Name) Display Automatically displays the station name transmitted by the RDS station. RDS Auto Memory function ( Automatically selects and stores up to 30 RDS stations in the preset memory. If fewer than 30 RDS stations have been stored in the preset memory, regular FM stations will be stored in the remaining places. Radio text function Displays the radio text data transmitted by some RDS stations when you press the DISPLAY key. The "RDS" indicator lights up when an RDS broadcast (signal) is received. SP AUDIO BAND (AUTO) TUNING/SKIP Operations 1 Use the input selector to select the tuner. 2 Use the BAND key to select the desired broadcast band. Each press switches the band as follows: 1 FM 2 AM "AM" or "FM" indicator 7. 5) 7. 5) FM MHz AUTO MEMO. STEREO ST. TUNED A B TI. VOL L R SW 3 Use the AUTO key to select the desired tuning method. Each press switches the tuning method as follows: 1 AUTO lit (auto tuning) 2 AUTO not lit (manual tuning) FM MHz AUTO RDS EON PTY TP TA NEWS -- 9 2. 5) FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO. TUNED Note Some functions and function names may differ for certain countries and areas. · Normally, set to "AUTO" (auto tuning). If the radio waves are weak and there is a lot of interference, switch to manual tuning. (With manual tuning, stereo broadcasts will be received in monaural. ) Before using a function utilizing the RDS, be sure to perform the RDS Auto Memory operation by referring to the description in "Presetting RDS stations (RDS AUTO MEMORY)". ( 4 Use the MULTI CONTROL (TUNING/SKIP) to select the station. Frequency display Lights when a broadcast is being received in stereo. FM MHz AUTO MEMO. -Auto tuning : Manual tuning : 8 9. )) STEREO ST. TUNED "TUNED" is displayed when a station is received The next station is tuned automatically. Turn the knob (press the key) to select the desired station. Listening to radio broadcasts KRF-V8010D (En/T) Using the DISPLAY key DISPLAY 3 Press and hold the MEMORY key for more than 2 seconds. SP A B TI. VOL MUTE RDS EON PTY TP TA NEWS 19 L R SW AUTO MEMOR Y FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO. [. . . ] 200 mV / 10 k Output level / impedance TAPE REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV / 1 k PRE OUT (CENTER, SURROUND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 V / 1 k PRE OUT (SUBWOOFER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 V / 600 Tone control BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]