User manual KLIPSCH CHORUS II

[. . . ] PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. USE only with a cart, stand, tripod, bracket, or table specifiedby the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. UNPLUG this apparatus during lightning storms or when unused for long periods of time. [. . . ] If nothing has been saved in the selected preset, the display will read "Preset Empty". From this screen, press the Down or Up touch key to access other control settings. Page 6 Page 7 Features and Controls - 2 Features and Controls - 3 EQ Mode This screen is used to select two different bass emphasis settings titled "Punch" and "Depth". They are designed to complement different types of program material, such as movie soundtracks or music. The "Punch" setting emphasizes the 55Hz region, while the "Depth" setting boosts the 30Hz range. A third setting is titled "Flat", which defeats these two settings. From this screen, press the Down or Up touch key to access other control settings. Room Correction This screen is used to activate the automatic Adaptive Room Correction (ARC) feature. Plug the supplied microphone into the "MIC IN" jack on the subwoofer's rear panel and place it in the intended listening position. "Calibrate" will be displayed along with the ascending frequency of the test tone and a bar graph of the sound level (loudness). The subwoofer will measure the room's acoustic effect and compensate for it. When the calibration sequence is complete, "Calibration Successful!" will be displayed. If the subwoofer's volume level is too low or the microphone was either disconnected or improperly connected, "Calibration Unsuccessful" will be displayed. It is suggested that you write down all of your settings for future reference in case the keypad is unlocked and your settings are changed by another user. From this screen, press the Down or Up touch key to access other control settings. This section describes the features and connections found on the amplifier on the back panel of the subwoofer. It also describes the manner for connecting a second subwoofer as a "slave" unit to the primary subwoofer. Power On/Off This is the main AC power switch for the subwoofer. This switch must be in the "On" position for the subwoofer to operate and for the "Auto On" feature to function. Set this switch to the "Off" position if the subwoofer will not be used for an extended period of time (i. e. vacation) or when making any connections to the subwoofer. System Info Press This screen is used to access the software "Version" number and "System Reset" function to clear all user settings and memories (Refer to the "Save Settings" section of this manual). If the "System Reset" function is activated all of the memory presets are erased and the subwoofer's controls are restored to the default settings of: "Volume 0db", "EQ Mode Flat", "Lowpass Off LFE Mode", "Phase 0°", "Disp Brightness" (highest level) and "Power Always On. For more information on the controls mentioned in this manual and on the bass management settings of your electronics, see your authorized Klipsch dealer or visit www. klipsch. com. USB This USB computer interface allows access to additional advanced features within the subwoofer's ARC room correction software. Optional, proprietary Klipsch software and a higher level of technical knowledge are required to correctly utilize this capability. This port can also function as an alternative control interface with A/V control systems that can utilize a USB connection. Please contact your authorized Klipsch dealer or Klipsch Technical Support for more information. Line Out There are both RCA-type and XLR connections provided for line out signals. [. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]